Page 2 - Installation & Safety Guide; Download the complete document set from
AT-8600 Series Installation & Safety Guide AT-8624T/2M AT-8624PoE AT-8648T/2SP Download the complete document set from www.alliedtelesis.com/support/software
Page 4 - Table of Contents
Installation & Safety Guide 3 Table of Contents Models Covered by this Guide ...................................................................................... 4 Package Contents ............................................................................................................. 4 S...
Page 5 - AT-8600 Series Installation & Safety Guide; Preinstalled AT-A65 expansion modules; Expansion Module Installation and Safety Guide
4 AT-8600 Series Switch Models Covered by this Guide This document includes information about the following switches: ■ AT-8624T/2M 24-port 10BASE-T/100BASE-TX ■ AT-8624PoE 24-port 10BASE-T/100BASE-TX ■ AT-8648T/2SP 48-port 10BASE-T/100BASE-TX You can download updates to this document from www.allie...
Page 6 - Selecting a Site; There should be adequate airflow around the switch and its vents.
Installation & Safety Guide 5 Selecting a Site Before you install the switch, review the following considerations about its location. ■ The switch requires an ambient temperature range of 0 º C to 40º C (32º F to 104º F). ■ There should be adequate airflow around the switch and its vents. ■ The ...
Page 7 - Installing the Switch; Before you begin; software; Warning
6 AT-8600 Series Switch Installing the Switch Ports on the switch are suitable only for connections within buildings (intra-building) and with cables unexposed to the outside. Before you begin ■ Read the safety information. For your well-being and that of the equipment, read the safety information i...
Page 8 - Procedure; AT-A65 Expansion Module Installation and Safety Guide
Installation & Safety Guide 7 Procedure 1. If you have any optional expansion modules, install them first. The AT-8600 Series switches support the AT-A45/xx, AT-A46, AT-A47, and AT-A65 expansion modules. Install them by following the instructions in the relevant guide: • AT-A65 Expansion Module ...
Page 9 - Never; force a transceiver into or out of a socket.
8 AT-8600 Series Switch . Slide the transceiver into the SFP socket, and firmly press it until it engages. To remove it, first release it by gently pulling the release lever, and then pull it out of the socket. Never force a transceiver into or out of a socket. When an SFP is installed into one of t...
Page 10 - Figure 2: AT-8624PoE front and rear panel with AC power inlet
Installation & Safety Guide 9 Figure 2: AT-8624PoE front and rear panel with AC power inlet Figure 3: AT-8648T/2SP front and rear panel with AC power inlet 7. Check that the PWR LED on the switch’s front panel is green. If the PWR (power) LED fails to light, refer to the AT-8600 Series Hardware ...
Page 11 - Connecting the Switch; Using the CLI to configure a switch; and the password is; friend; At the login prompt, enter the login name and password:; To change the account password, use the; set password
10 AT-8600 Series Switch Connecting the Switch Some configuration is necessary to enable the switch’s advanced switching capabilities. This is achieved via the Command Line Interface (CLI). On the AT-8624T/2M, you can also use the Graphical User Interface (GUI). Using the CLI to configure a switch 1...
Page 12 - topic; Using the GUI to configure the
Installation & Safety Guide 11 5. Configure online help. Before using online help, you must configure the help file by using the command: set help=< filename> .hlp Help files have an HLP extension. To see a list of help files loaded on your switch, use the command: show files=*.hlp 6. Conf...
Page 13 - “Using; switch
12 AT-8600 Series Switch 2. Connect the PC to the switch. Use an Ethernet cable to connect an Ethernet card on the PC to any one of the switch ports. You can browse to the router through any VLAN, as long as you give that VLAN an IP address. These instructions assume you are using vlan1. All switch ...
Page 14 - Checking LEDs; System LEDs
Installation & Safety Guide 13 Checking LEDs The following tables outline how the switch and expansion modules report faults and operational activities. Expansion modules are optional and can be purchased separately. Use the Mode Select button to toggle the Mode LEDs to the desired state. Toggli...
Page 19 - Obtaining Documentation and Resources; Other resources; Trivial File Transfer Protocol; Contacting us
18 AT-8600 Series Switch Obtaining Documentation and Resources The complete document set for the AT-8600 Series switches includes: ■ This Installation & Safety Guide , which also provides safety and statutory information for the AT-8600 Series switch and its expansion options. ■ The AT-8600 Seri...
Page 20 - Standards
Installation & Safety Guide 19 Standards Where applicable, the products in this document meet the following standards: Category Approval Agency and Requirement UL60950-1CAN/CSA-C22.2 No. 60950-1-03EN60950-1EN60825-1 Electromagnetic Compliance FCC CFR47 Part 15 Class AEN55022 Class AEN61000-3-2EN...
Page 21 - Safety
20 AT-8600 Series Switch Safety WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING: Class 1 Laser product. WARNING: Do not stare into the laser beam. CAUTION: Use of controls or adjustments of perform...
Page 22 - Sicherheit; WARNUNG Laserprodukt der Klasse 1.
Installation & Safety Guide 21 Lithium Battery - Should only be changed by authorised service personnel. CAUTION: Danger of explosion if battery incorrectly replaced. Replace only with Lithium Battery, type CR2032, and dispose of in accordance with the manufacturer’s recommendations and all loca...
Page 24 - Sikkerhed
Installation & Safety Guide 23 Sikkerhed ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. ADVARSEL Laserprodukt av klasse 1. ADVARSEL Stirr ikke på strålen. ELEKTRISKE FORHOLD...
Page 25 - Veiligheid
24 AT-8600 Series Switch Lithium batteri - Bør kun udskiftes af uddannet og kvalificeret tekniker. ADVARSEL : Eksplosionsfare, hvis batteriet udskiftes ukorrekt. Udskift kun med samme eller en tilsvarende type der anbefales af producenten. Kassér brugte batterier i overensstemmelse med producentens ...
Page 26 - Sécurité
Installation & Safety Guide 25 BEDRIJFSTEMPERATUUR: De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden Celsius. ELEKTRISCH: OVERBELASTING VAN WISSELSTROOM HOOFDCIRCUIT Tijdens de installatie van het produkt dient men rekening te houden met de gecombineerde waarden op d...
Page 27 - ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE; Turvallisuus; VAROITUS Luokan 1 Lasertuote.
26 AT-8600 Series Switch ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être branchée dans une prise femelle correctement mise à la terre car des tensions dangereuses risqueraient d’atteindre les pièces métalliques accessibles à l’utilisateur. EQUIPE...
Page 28 - SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA
Installation & Safety Guide 27 SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA VAROITUS: SÄHKÖISKUVAARA Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain koulutettu ja pätevä teknikko. SALAMANISKUVAARA H...
Page 29 - Norme di Sicurezza
28 AT-8600 Series Switch Norme di Sicurezza AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. AVVERTENZA Prodotto laser di Classe 1. AVERTENZA Non fissare il raggio con gli occ...
Page 30 - Sikkerhet
Installation & Safety Guide 29 ATTENZIONE: CARICAMENTO MECCANICO - Il montaggio del dispositivo sul supporto va effettuato in maniera tale da evitare qualsiasi potenziale condizione di pericolo eventualmente dovuta al montaggio irregolare. Batteria al litio - Va sostituita solo da un tecnico spe...
Page 31 - Segurança
30 AT-8600 Series Switch FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med romtemperatur for avkjøling. DRIFTSTEMPERATUR: Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader celsius. ELEKTRISK OVERBELASTNING PÅ AC HOVEDKRETSLØP Når produktet inst...
Page 32 - ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1
Installation & Safety Guide 31 ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1 DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O plugue de alimentação deve ser conectado a uma tomada com adequada ligação de fio terra. Tomadas sem adequada ligação de fio terra podem transmitir voltagens perig...
Page 33 - Seguridad; AVISOS ELECTRICOS
32 AT-8600 Series Switch Seguridad ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. ¡ADVERTENCIA! Producto láser Clase 1. ¡ADVERTENCIA! No mirat fijamente el haz. A...
Page 34 - Säkerhet; VARNING! Laserstrålning när enheten är öppen.
Installation & Safety Guide 33 ATENCION: CARGA MECANICA - El montaje del equipo en el bastidor debe realizarse de manera tal que no cause una condición peligrosa debido a la distribución desigual del peso. Batería de litio - Sólo deberá ser cambiada por un técnico entrenado y calificado. ATENCIO...
