Allied Telesis AT-6101GP - Manual

5 Table 1. Twisted Pair Cable for the 10/100/1000Base-T Ports .......................................................................................... 13Table 2. 10/100Base-TX Port LEDs ...................................................................................................................

7 Preface This guide contains the installation instructions for the AT-6101 PoE Injector Installation Guide. This preface contains the following sections: ❒ “Document Conventions” on page 8 ❒ “Allied Telesis Contact Information” on page 9

Preface 8 Document Conventions This document uses the following conventions: Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a ...

AT-6101 PoE Injector Installation Guide 9 Allied Telesis Contact Information If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/support . You can find links ...

11 Chapter 1 Overview This chapter contains the following sections:  “Features” on page 12  “Hardware Description” on page 14  “LEDs” on page 15

Chapter 1: Overview 12 Features Here are the features of this product: AT-6101GP PoE Injector The major features of the AT-6101GP PoE Injector are:  Power over Ethernet Injector for 10/100/1000BaseT  Remote power feeding  Overload and short circuit protection  Mixes Ethernet and power into RJ-45...

AT-6101 PoE Injector Installation Guide 13 Cable Requirements The cable requirements of the ports are given in Table 1. Port Pinouts Refer to Table 7 on page 28 for the port pinouts of the 10/100Base-TX/1000Base-T twisted pair ports. Table 1. Twisted Pair Cable for the 10/100/1000Base-T Ports Cable ...

Chapter 1: Overview 14 Hardware Description The AT-6101GP PoE Injector is shown in Figure 1. Figure 1. AT-6101GP PoE Injector DATA IN Port: This port, shown in Figure 1, in is an RJ-45 Ethernet connector where data is received and transmitted through the AT-6101GP PoE Injector. DATA OUT Port: This p...

AT-6101 PoE Injector Installation Guide 15 LEDs The LEDs of the AT-6101GP PoE Injector are shown in Figure 3 and described in Table 2. Figure 3. AT-6101GP LEDs Table 2. 10/100Base-TX Port LEDs LED State Description AC Power Off No AC power is being provided to the unit. Solid Green AC power is being...

17 Chapter 2 Installation You may install the AT-6101GP PoE Injector on a table or on a wall. This chapter contains the following installation procedures:  “Reviewing Safety Precautions” on page 18  “Choosing a Site for the AT-6101GP PoE Injector” on page 20  “Unpacking the AT-6101GP PoE Injector...

Chapter 2: Installation 18 Reviewing Safety Precautions Please review the following safety precautions before you begin to perform the installation procedure. Note The  indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements . Warning ...

Chapter 2: Installation 20 Choosing a Site for the AT-6101GP PoE Injector Observe these guidelines when planning the installation of the AT-6101GP  If you plan to install the power injector on a table, the table should be level and stable.  The power outlet should be located near the power injecto...

AT-6101 PoE Injector Installation Guide 21 Unpacking the AT-6101GP PoE Injector The AT-6101GP PoE Injector comes with the items listed in Table 4. Verify that the contents of the shipping container matches the items listed. If any item in the shipping container is missing or damaged, contact your Al...

Chapter 2: Installation 22 Installation Procedures Depending on where you install the unit. perform the following procedures when installing the AT-6101GP PoE Injector:  ”Table Top Installation” or ”Wall Installation”  “Ethernet Cable Installation” on page 23  “AC Power Cord Installation” on page...

AT-6101 PoE Injector Installation Guide 23 2. Install the two wall anchors into the wall at the locations marked in the previous step. The anchors require 0.635 mm (0.25 in.) holes. 3. Hold the power injector on the wall so that the mounting holes align with the anchors previously installed. Secure ...

Chapter 2: Installation 24 AC Power Cord Installation Depending on your installation, connect the AC power cord as shown in Figure 8 (table top installation) or Figure 9 (wall installation). Figure 8. Connecting AC Power Cord for Table Top Installation Figure 9. Connecting AC Power Cord for Wall Ins...

25 Chapter 3 Troubleshooting This chapter contains suggestions on how to troubleshoot the installation of the AT-6101GP PoE Injector if a problem occurs. Problem: All PoE injector LEDs are off even though the ports are connected to network devices. Solution: Verify that AC power is connected to the ...

27 Appendix A Technical Specifications Physical Specifications Environmental Specifications Power Specifications Table 3. Physical Specifications Dimensions (H x W x D) 36 mm x 65 mm x 140 m Weight 300 grams (0.66 lb) Table 4. Environmental Specifications Operating Temperature 0° C to 40° C (32° F t...

Appendix A: Technical Specifications 28 Certifications RJ-45 Twisted Pair Port Pinouts Figure 10 illustrates the pin layout of the RJ-45 connectors and ports. Figure 10. RJ-45 Socket Pin Layout (Front View) Table 7 lists the pin signals for 10 and 100 Mbps. Table 6. Certifications EMI (Emissions) FC...