Page 3 - Installation & Safety Guide; Electrical Safety and Emission Compliance Statement; STANDARDS
Installation & Safety Guide 3 Electrical Safety and Emission Compliance Statement STANDARDS : This product meets the following standards: Category Approval Agency and Requirement UL60950-1CAN/CSA-C22.2 No. 60950-1-03EN60950-1EN60825-1 Electromagnetic Compliance FCC CFR47 Part 15 Class AEN55022 C...
Page 5 - Table of Contents
Installation & Safety Guide 5 Table of Contents Electrical Safety and Emission Compliance Statement ............................................. 3 Models Covered By This Guide .................................................................................... 6 Package Contents ..................
Page 6 - Models Covered By This Guide; Package Contents
6 AT-8600 Series Switch Models Covered By This Guide This Installation & Safety Guide includes information on these models: ■ AT-8624T/2M 24-port 10BASE-T/100BASE-TX Layer 3 Fast Ethernet Switch ■ AT-8624PoE 24-port 10BASE-T/100BASE-TX Layer 3 Fast Ethernet Switch ■ AT-8648T/2SP 48-port 10BASE-T...
Page 7 - Selecting a Site
Installation & Safety Guide 7 Selecting a Site You can install the switch in a standard 19-inch rack, on a level surface such as a desktop or bench, or against a wall using the optional wall-mount kit. How to install the switch using the 19-inch rack-mount kit is described below. . When you inst...
Page 8 - How to Install the Switch; Prepare to install the switch
8 AT-8600 Series Switch How to Install the Switch Warning All versions of this equipment must be earthed. Prepare to install the switch 1. Read the safety information Read the safety information included in this Installation & Safety Guide . This Installation & Safety Guide is also on the Do...
Page 9 - Check the supply voltage and the switch’s rated voltage
Installation & Safety Guide 9 • Mount the switch in the rack using standard screws (these are not provided). 7. Install SFPs For the AT-8648T/2SP, you may also need an optional SFP (Small Form-factor Pluggable module). Do not look into the optical ports of SFP cables or transceivers. Invisible l...
Page 10 - Connect the data cables
10 AT-8600 Series Switch 9. Apply AC power to the switch Plug the power cord into the AC power connector. This is on the switch’s rear panel, as shown in the below figures. Figure 1: AT-8624T/2M front and rear panel with AC power inlet. Figure 2: AT-8624PoE front and rear panel with AC power inlet F...
Page 11 - How to Configure the Switch; Using the CLI to configure a switch; Set the communication parameters.; friend
Installation & Safety Guide 11 How to Configure the Switch Some configuration is necessary to enable the switch’s advanced switching capabilities. This is achieved via the Command Line Interface (CLI). On the AT-8624T/2M, you can also use the Graphical User Interface (GUI). Using the CLI to conf...
Page 12 - Change password and display help.; Using the GUI to configure the; Select a PC to use and identify its subnet.; switch; ’s command line interface.
12 AT-8600 Series Switch 4. Change password and display help. Change the password as soon as possible because a manager account left with the default password is a serious security risk. Remember the new password as there is no way to retrieve it if it is lost. To change the account password, use th...
Page 14 - LEDs on AT-8600 Series Switches; Note
14 AT-8600 Series Switch LEDs on AT-8600 Series Switches The following tables outline how the switch and expansion modules report faults and operational activities. Expansion modules are optional and can be purchased separately. Contact an authorised Allied Telesis distributer or reseller, or visit ...
Page 19 - Documentation and Tools CD-ROM
Installation & Safety Guide 19 Documentation and Tools CD-ROM The Documentation and Tools CD-ROM bundled with each switch contains the complete documentation set for AT-8600 Series switches and their expansion options, as well as tools to manage the switch. The documentation and tools CD-ROM inc...
Page 20 - Safety
20 AT-8600 Series Switch Safety WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING: Class 1 Laser product. WARNING: Do not stare into the laser beam. C AUTION: Use of controls or adjustments of perfor...
Page 21 - Sicherheit
Installation & Safety Guide 21 Lithium Battery - Should only be changed by authorised service personnel.C AUTION: Danger of explosion if battery incorrectly replaced. Replace only with Lithium Battery, type CR2032, and dispose of in accordance with the manufacturer’s recommendations and all loca...
Page 23 - Sikkerhed
Installation & Safety Guide 23 Sikkerhed ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. ADVARSEL Laserprodukt av klasse 1. ADVARSEL Stirr ikke på strålen. ELEKTRISKE FORHOLD...
Page 24 - Veiligheid
24 AT-8600 Series Switch Lithium batteri - Bør kun udskiftes af uddannet og kvalificeret tekniker.ADVARSEL : Eksplosionsfare, hvis batteriet udskiftes ukorrekt. Udskift kun med samme eller en tilsvarende type der anbefales af producenten. Kassér brugte batterier i overensstemmelse med producentens i...
Page 25 - Sécurité
Installation & Safety Guide 25 BEDRIJFSTEMPERATUUR: De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden Celsius. ELEKTRISCH: OVERBELASTING VAN WISSELSTROOM HOOFDCIRCUITTijdens de installatie van het produkt dient men rekening te houden met de gecombineerde waarden op de...
Page 26 - Turvallisuus
26 AT-8600 Series Switch ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUECE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être branchée dans une prise femelle correctement mise à la terre car des tensions dangereuses risqueraient d’atteindre les pièces métalliques accessibles à l’utilisateur. EQUIPEM...
Page 28 - Norme di Sicurezza
28 AT-8600 Series Switch Norme di Sicurezza AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. AVVERTENZA Prodotto laser di Classe 1. AVERTENZA Non fissare il raggio con gli occ...
Page 29 - Sikkerhet
Installation & Safety Guide 29 ATTENZIONE: C ARICAMENTO MECC ANICO - Il montaggio del dispositivo sul supporto va effettuato in maniera tale da evitare qualsiasi potenziale condizione di pericolo eventualmente dovuta al montaggio irregolare. Batteria al litio - Va sostituita solo da un tecnico s...
Page 30 - Segurança
30 AT-8600 Series Switch FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med romtemperatur for avkjøling. DRIFTSTEMPERATUR: Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader celsius. ELEKTRISK OVERBELASTNING PÅ AC HOVEDKRETSLØPNår produktet insta...
Page 31 - Seguridad
Installation & Safety Guide 31 ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O plugue de alimentação deve ser conectado a uma tomada com adequada ligação de fio terra. Tomadas sem adequada ligação de fio terra podem transmitir voltagens perigo...
Page 33 - Säkerhet
Installation & Safety Guide 33 Säkerhet VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. VARNING! Laserprodukt av klass 1. VARNING! Laserstrålning när enheten är öppen. TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICI...
Page 35 - EC Declaration of Conformity
Installation & Safety Guide 35 EC Declaration of Conformity We: ALLIED TELESIS LABS LIMITED27 NAZARETH AVENUECHRISTCHURCH 8024NEW ZEALAND Declare under our sole legal responsibility that the following product meets the safety, protection and conformity requirements of council directives 73/23/EE...
