Page 2 - Table of
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT © Copyright, Alliance Laundry Systems LLCAll rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 2-09-30 1 Table ...
Page 3 - Introduction; Model Identification; Gas
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2 2-09-30 Tumblers – 50 and 75 Introduction Model Identification Includes models with the following control suffixes : TMB795C Gas Steam/Thermal Oil Electric 50 Pound IPD50G2-IT050L IPD50G2-IT050N IPD50S2-IT050S IPD50S2-IT050T IPD50...
Page 5 - Specifications and Dimensions
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 4 2-09-30 Specifications and Dimensions N/A = Not Applicable Specifications 50 Pound 75 Pound Noise level measured during operation at operator position of 3.3 feet (1 meter) in front of machine and 5.2 feet (1....
Page 6 - Cabinet Dimensions
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 2-09-30 5 Cabinet Dimensions * Fire suppression system optional - may not be on machine. TMB2293N TMB2293N C B F D A K G J E I H Models A B C D E* F 50 Pound Gas and Electric 30.75 in. (781 mm) 33.87 in. (860 mm...
Page 7 - Exhaust Outlet Locations
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 6 2-09-30 Exhaust Outlet Locations TMB2238N A B C A B C 5.375 in. (137 mm) 8 in. (203 mm) 13.375 in. (340 mm)
Page 8 - Gas Connection Locations; Diameter
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 2-09-30 7 Gas Connection Locations TMB2239N A B Diameter A B 3/4 in. NPT 14.75 in. (375 mm) 65.75 in. (1670 mm)
Page 9 - Electrical Connection Locations; NOTE: These figures are approximate dimensions only.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 8 2-09-30 Electrical Connection Locations TMB2240N TMB82240N GAS AND STEAM ELECTRIC A B B A A B 3.25 in. (83 mm) 75.5 in. (1918 mm) NOTE: These figures are approximate dimensions only.
Page 10 - Steam Connection Locations
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 2-09-30 9 Steam Connection Locations TMB2241N C A B D Diameter A B C D 3/4 in. NPT 15.5 in. (394 mm) 78.25 in. (1988 mm) 7.5 in. (190 mm) 64.75 in. (1645 mm)
Page 11 - Installation; Pre-Installation Inspection
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 10 2-09-30 Installation Pre-Installation Inspection Upon delivery, visually inspect the crate, carton and parts for any visible shipping damage. If the crate, carton, or cover is damaged or signs of possible dam...
Page 12 - Tumbler Enclosure; WARNING; construction must conform to the minimum clearances.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 2-09-30 11 Tumbler Enclosure Figure 1 TMB2242N NOTE: Shaded areas indicate adjacent structure. 1 0.5 in. (13 mm) recommended between machines for removal or installation 2 Allow 2-4 in. (51-102 mm) opening at to...
Page 13 - Exhaust Requirements; Layout; Required Make-Up Air Opening
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 12 2-09-30 Exhaust Requirements Layout Whenever possible, install tumblers along an outside wall where duct length can be kept to a minimum, and make-up air can be easily accessed. Elbows and long vents tend to ...
Page 14 - Figure 2; Individual Venting; Duct
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 2-09-30 13 NOTE: Exhaust ducts must be constructed of sheet metal or other noncombustible material. Such ducts must be equivalent in strength and corrosion resistance to ducts made of galvanized sheet steel not ...
Page 15 - Consult your local building code for regulations which
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 14 2-09-30 Figure 2 NOTE: Do not install wire mesh or screen in exhaust duct opening to avoid lint build-up or impacting proper discharge of air from tumblers. NOTE: Where exhaust duct pierces a combustible wall...
Page 16 - Manifold Venting; Figure 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 2-09-30 15 Manifold Venting While it is preferable to exhaust tumblers individually to the outdoors, a main collector duct may be used if it is sized according to Figure 4 and Figure 5 . This illustration indica...
Page 17 - Duct Station
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 16 2-09-30 Figure 4 TMB2019N 1 NOTE: Where the exhaust duct pierces a combustible wall or ceiling, the opening MUST be sized per local codes. 2 Outlet duct diameter 3 45° typical L K J I H G F E D C B A 3 1 2 ON...
Page 19 - 0 Pound Gas and Steam Models; Refer to
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 18 2-09-30 50 Pound Gas and Steam Models Refer to Table 4 . NOTE: Wire sizes were obtained from the Canadian Electrical Code for 75 C. wire and are intended for use as a guideline only. Electrical connections sh...
Page 20 - 5 Pound Gas and Steam Models
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 2-09-30 19 75 Pound Gas and Steam Models Refer to Table 5 . NOTE: Wire size and breaker ratings were obtained from the Canadian Electrical Code for 75 C. wire and are intended for use as a guideline only. Electr...
Page 21 - 0 and 75 Pound Electric Models
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Tumblers – 50 and 75 20 2-09-30 50 and 75 Pound Electric Models Refer to Table 6 . NOTE: Wire size and breaker ratings were obtained from the Canadian Electrical Code for 75 C. wire and are intended for use as a guideline only. Elec...
