Alliance HF185 - Manual

7 2 Environmental Disposal of Unit This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be hande...

8 Explanation of Safety Messages Throughout this manual and on machine decals, you will find precautionary statements (“DANGER”, “WARNING” and “CAUTION”) followed by specific instructions. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining t...

9 Important Safety Instructions WARNING To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions: 1. Read all instructions before using the washer.2. Refer to the GROUNDING INSTRUCTIONS in the installation Manual for the pr...

10 22 21. Loading door MUST BE CLOSED any time the washer is to fill, tumble, or spin. DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open. 22. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warni...

11 Operator Safety WARNING NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury. To ensure the safety of machine operators, the following maintenance checks must be performed daily:1. Prior to operating the machine, verify that all warnin...

3 12 3 Technical data HF150, IHF150, IHF033, CHF150, CHF033 Technical data and dimensions METRIC US Capacity (dry weight) Ratio [kg/Lit] 1:11 13,2 kg 29.10 lb. 1:10 14,5 kg 31.97 lb. 1:9 16,1 kg 35.49 lb. Cylinder Diameter 680 mm 26.77 inch Depth 400 mm 15.75 inch Volume 145 Lit 5.12 ft³ Cabinet Hei...

Label 1 1/2 1/2 1/3 Label 2 20 4 Installation and Connection Instructions Surface CAUTION Ensure that the machine is installed on a level floor of sufficient strength and that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to ...

HF234-304 Label 3 Label 4 HF150-185 4 21 To prevent damage during transportation, the machine has been equipped with four red transport brackets to eliminate every possible movement of the tub. After the machine has been placed level, take off the service panel and back panel to remove these transpo...

26 4 The machine is delivered with hoses with 3/4" connections. These hoses fit the water inlet valves of the machine and the main water inlet taps. All the inlet valves have to be connected. To ensure the optimal functioning of the water inlet valves, the water pressure on the inlet should be b...

4 27 Electrical installation ImportantElectrical ratings are subject to changes. Refer to serial plate decal for electrical ratings information specific to your machine. WARNING Hazardous Voltage. Can cause shock, burn or cause death. Allow machine power to remain off for two minutes prior to workin...

4 28 Use wire sizes indicated in Table 3 through 6 for runs up to 50 feet. Use next larger size for runs of 50 to 100 feet. Use two sizes larger for runs greater than 100 feet. For personal safety and proper operation, the washer-extractor must be grounded in accordance with state and local standard...

4 Label 5 29 Connection label: Machine power connections are made at the back of the machine. Three or four conductor power cable is the recommended method (See chapter electrical specs for minimum cable requirements, if local electrical codes exceed these requirements, follow local codes). The numb...

4 31 WARNING The washer-extractor should be connected to an individual branch circuit not shared with lighting or other equipment. Electrical Specifications HF150, IHF150, IHF033, CHF150, CHF033 150 liters / 33 pounds Boiler Fed/Steam Heat Electric Heat Code Voltage Cycle Phase Wire Full Load Amps R...

Label 6 Label 7 4 35 The liquid soap connection consists of 8 connections for liquid soap (See Label 6). The central opening is used for ventilation. Liquid soap connection (option) Connection of the liquid soap hoses WARNING Dangerous Chemicals. May damage eyes and skin. Wear eye and hand protectio...

Label 11 Label 12 Label 13 Label 14 4 A 37 Connection of a central operating panel for coin machines (option) WARNING To reduce the risk of electric shock, disconnect this appliance from the power supply before attempting any user maintenance. Turning the controls to the OFF position does not discon...

5 2 3 4 5 3 1 6 7 7 7 38 Steam connection Machines with steam heating must have a steam valve between the steam installation and the machine. WARNING Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam m...

6 Label 15 Label 16 39 Internal connections of the electrical heating NOTE: Other executions are available as options. 3 AC 1 AC Technical remarks Heating 3x230V R5 3x400V R5 4,2kw 3x1,4kw See Label 15 LC1D0901 See Label 16 LC1D0901 6kw 3x2kw See Label 15 LC1D0901 See Label 16 LC1D0901 9kw 3x3kw See...

7 40 Maintenance instruction of the machine  Clean the entire cabinet of the machine regularly and remove all traces of soap, etc....  Remove all detergent residue in the soap dispenser with hot water.  Clean the door gasket and remove all detergents and other products.  Shut off the main water,...

7 41  Verify that the belts are running in the middle of the basket pulley.  Verify the belt tension according to the table below. Belt tension measurements should be taken as close as possible to the center of the belt span (see figure). Annual maintenance Belt tension: Belt tension testing table...

8 Label 17 Label 18 42 Contact Information Nameplate Nameplate Location The nameplate is located at the rear of the machine. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. See Labels 17 and 18.

8 43 Replacement Parts If literature or replacement parts are required, contact the source from which the machine was purchased or contact the phone numbers or websites shown on the nameplate. Position of the Serial plate

9 44  In case of important malfunctions and deficiencies, which you cannot resolve yourself, contact your distributor. Repair and after-sales service Machine : Type: ......................................................................................Program: .........................................