Page 3 - WARNING; WARNING; that the tumble dryer is properly grounded.
Front Matter Installation must conform with local codes or, in the absence of local codes, with: In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/ NFPA 54 “National Fuel GasCode” and Standard ANSI/NFPA 70 “National Electric Code.” In Canada, ins...
Page 5 - Table of Contents; Introduction
Table of Contents Introduction ........................................................................................... 8 Model Identification ....................................................................................... 8 Contact Information ...............................................
Page 8 - Model Identification; Information in this manual is applicable to these models:; Gas
Introduction Model Identification Information in this manual is applicable to these models: Gas Steam/Thermal Oil Electric 120 Series CA120L CA120N CK120N CT120L CT120N CU120L CU120N DR120G2-BA120L DR120G2-BA120N DR120G2-BK120N DR120G2-BT120L DR120G2-BT120N DR120G2-BU120L DR120G2-BU120N HA120L HA120...
Page 9 - Not Applicable
Gas Steam/Thermal Oil Electric 170 Series CA170L CA170N CK170N CT170L CT170N CU170L CU170N DR170G2-BA170L DR170G2-BA170N DR170G2-BK170N DR170G2-BT170L DR170G2-BT170N DR170G2-BU170L DR170G2-BU170N HA170L HA170N HK170N HT170L HT170N HU170L HU170N IPD170G2 IT170L IT170N SA170L SA170N SK170N ST170L ST17...
Page 10 - Contact Information; Figure 1
T = Thermal Oil Includes models with the following control suffixes R3 – reversing DX4 OPL RE – reversing LED OPL RQ – reversing dual digital timer RD – reversing DMP OPL RM – reversing OPL micro RU – reversing UniLinc OPL Contact Information If service is required, contact the nearest Factory Autho...
Page 11 - Explanation of Safety Messages; DANGER; Important Safety Instructions; Save These Instructions; • Do not install or store the tumble dryer where it will be ex-
Safety Information Explanation of Safety Messages Precautionary statements (“DANGER,” “WARNING,” and“CAUTION”), followed by specific instructions, are found in thismanual and on machine decals. These precautions are intendedfor the personal safety of the operator, user, servicer, and thosemaintainin...
Page 13 - Specifications and Dimensions; Specifications
Specifications and Dimensions Specifications and Dimensions Refer to machine serial plate for additional specifications. Specifications 120 Series 170 Series 200 Series Noise level measured during operationat operator position of 3.3 feet (1 meter)in front of machine and 5.2 feet (1.6 me-ters) from ...
Page 14 - 20 Series Tumble Dryer Dimensions and Exhaust Outlet Locations; Cabinet Dimensions
Specifications 120 Series 170 Series 200 Series Steam Models Net Weight (approximate): Pounds [kg] 1,375 [624] 1,675 [761] 1,808 [820] Steam Connection 3/4 in. NPT inlet 3/4 in. NPT outlet 3/4 in. NPT inlet 1 in. NPT outlet 3/4 in. NPT inlet 1 in. NPT outlet Steam Coil Rating at 100 psig: Btu/hr. [k...
Page 15 - Exhaust Outlet Dimensions and Locations; Models
Cabinet Dimensions 120L/N/E 31.38 in. [797mm] 32.5 in. [826mm] 48.91 in. [1,242mm] 49.91 in. [1,268mm] 67.92 in. [1,725mm] 45.38 in. [1,153mm] 120S 31.38 in. [797mm] 32.5 in. [826mm] 48.91 in. [1,242mm] 49.91 in. [1,268mm] 67.92 in. [1,725mm] 45.38 in. [1,153mm] Models G H I J* K* L* 120L/N/E 46.38 ...
Page 16 - Top View of Exhaust Duct
170 and 200 Series Tumble Dryer Dimensions and Exhaust Outlet Locations TMB2397N_SVG1 V Y X W G F L H J K E D C I B A 1 1. Top View of Exhaust Duct Cabinet Dimensions Models A B C D E F 170L/N/S 33.86 in. [860mm] 32.5 in. [ 826mm] 50.75 in. [1,289mm] 51.75 in. [1,314mm] 68.85 in. [1,749mm] 52.12 in....
Page 20 - Electric Connection Location for Electric Models
Models Steam Outlet Diameter B1 B2 D 120S 3/4 in. NPT 34.625 in. [879 mm] 13.125 in. [333 mm] 68.5 in. [1,740 mm] 170S 1 in. NPT 44.125 in. [1,133 mm] 9 in. [229 mm] 72.125 in. [1,832 mm] 200S 1 in. NPT 44.125 in. [1,133 mm] 9 in. [229 mm] 72.125 in. [1,832 mm] Models Electrical Connection C E 120S ...
Page 22 - Pre-Installation Inspection; Figure 2
Installation Pre-Installation Inspection Upon delivery, visually inspect the crate, carton and parts for anyvisible shipping damage. If the crate, carton, or cover is damagedor signs of possible damage are evident, have the carrier note thecondition on the shipping papers before the shipping receipt...
Page 23 - NOTE: Shaded areas indicate adjacent structure.; Minimum clearance permitted for remainder:; Position and Level the Tumble Dryer; Check Local Codes and Permits
TMB2020N_SVG 4 3 1 5 6 7 8 2 NOTE: Shaded areas indicate adjacent structure. 1. 0.5 in. [13 mm] recommended between machines for removal or installation 2. Allow 2-4 in. [51-102 mm] opening at top of machine to aid in removal or installation. A removable trim piece may be used toconceal the opening;...
Page 24 - Figure 3
Call your local water company or the proper municipal authorityfor information regarding local codes. IMPORTANT: It is your responsibility to have ALLplumbing connections made by a qualified professio-nal to assure that the plumbing is adequate and con-forms to local, state, and federal regulations ...
Page 25 - Electrical Requirements; Auxiliary Alarm; Figure 5
To connect the two hoses (supplied with tumble dryer), insertrubber washers (from literature pack) in water inlet hose cou-plings. Refer to Figure 4 . TMB2008N_SVG 3 2 4 5 2 1 1. Lock 2. Hose Couplings 3. Y Valve 4. Inlet Hoses 5. Opening for Auxiliary Alarm Cable Figure 4 Connect inlet hoses to wat...
Page 26 - Before Placing Tumble Dryer into Serv-; Figure 6
TMB1999N_SVG1 6 7 5 4 3 1 2 1. Opening for Auxiliary Alarm Cable 2. Fuse 3. Auxiliary Alarm Fast-On Connection 4. Test Button 5. Light 6. Reset Button 7. Auxiliary Alarm Fast-On Connection Figure 5 Before Placing Tumble Dryer into Serv- ice 1. Remove or open all panels and check accessible bolts, nu...
Page 27 - Installing CE Gas Drying Tumble Dryer; General Information
Models Prepurge Time(seconds) Trial for Ignition(seconds) Reset LockoutCondition By: Models through3/10/13 CE and Australia 18 10 025, 030, 035, 055:Press reset button onrear of machine T30, T45: Press lightedreset button in rearcontactor box All others 1-3 10 Open loading door Models starting3/11/1...
Page 31 - Figure 7; Specific Conversion Procedures; Models through; How to Change Burner Orifice Size; Figure 8; How to Adjust Gas Valve Governor/Regulator
TMB2328N_SVG 4 3 2 1 1. Gas Shut-Off Valve (Ahead of pressure tap) (Not Sup-plied) 2. Pressure Tap 3. Gas Shut-Off Valve (Shown in closed position) (Not Sup-plied) 4. Specified Local Inlet Pressure Figure 7 Specific Conversion Procedures How to Convert Gas Valve from Regulated to Unregu- lated NOTE:...
Page 32 - Burner Orifice; Size Stamped on Orifice
Burner Orifice TMB2015N_SVG 1 1. Size Stamped on Orifice Figure 9 Installation 32 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Part No. 70458101ENR9
Page 33 - Exhaust Requirements; Layout; Model; Venting
Exhaust Requirements Exhaust Requirements WARNING A drying tumble dryer produces combustible lint. Toreduce the risk of fire, the tumble dryer must be ex-hausted to the outdoors. W057R1 WARNING To reduce the risk of fire, DO NOT use plastic or thinfoil ducting to exhaust the tumbler. W773 WARNING To...
Page 34 - Partition or bulkhead; Alternate Venting for 120 Series Tumble Dryers; Remove belt guard cover.
WARNING Improperly sized or assembled ductwork causes ex-cess back pressure which results in slow drying, lintcollecting in the duct, lint blowing back into theroom, and increased fire hazard. W355 NOTE: Exhaust ducts must be constructed of sheetmetal or other noncombustible material. Such ductsmust...
Page 35 - Individual Venting; Duct Diameter; Table 3; Manifold Venting; and
T496I_SVG B A A 2 1 1. Discard 2. Cover Figure 11 Individual Venting For maximum efficiency and performance, it is preferred to ex-haust tumble dryer(s) individually to the outdoors. IMPORTANT: At no point may the cross sectional areaof installed venting be less than the cross sectionalarea of the e...
Page 36 - One Manifold Assembly
Table 4 to determine equivalent ducting sizing. The collector duct may be rectangular or square in cross section, as long as the areais not reduced. Provisions MUST be made for lint removal andcleaning of the collector duct. The vent collector system must be designed so the static backpressure measu...
Page 37 - Duct Station; Table 4; represents units with the same vent size.; Refer to
Duct Station 120 Series 170/200 Series I 32 in. [813 mm] 36 in. [914 mm] J 33 in. [838 mm] 38 in. [965 mm] K 35 in. [889 mm] 40 in. [1,016 mm] L 36 in. [914 mm] 42 in. [1,067 mm] Table 4 NOTE: Table 4 represents units with the same vent size. If multiple vent sizes are used, consult a local HVACspec...
Page 38 - Gas Requirements; Table 5; Maximum
Gas Requirements Gas Requirements WARNING To reduce the risk of fire or explosion, DO NOT CON-NECT THE GAS LINE TO THE TUMBLE DRYER IFTHE GAS SERVICE IS NOT THE SAME AS THATSPECIFIED ON THE TUMBLE DRYER SERIALPLATE! It will first be necessary to convert the gasburner orifice and gas valve. Appropria...
Page 39 - Minimum; Gas Line to Tumble Dryer
Non-CE and Non- Australian Models Australian and Kore- an Models CE Mod- els Recommend-ed 11 in. w.c. 2.74 kPa 27.4 mbar Minimum 10 in. w.c. 2.49 kPa 24.9 mbar For converting Non-CE models from Natural Gas to L.P. Gas: Model Hertz Date Range Part No. 120 60 Through2/14/11 M4577P3 120 60 Starting2/15...
Page 40 - Gas Supply Pipe Sizing and Looping; Sediment traps, supply pressure taps and shut-off valves. Refer to
Gas Supply Pipe Sizing and Looping TMB2126N_SVG 1 2 3 4 5 6 7 8 9 M 6 8 7 4 5 3 2 1 9 10 11 12 1. Gas furnace [120,000 Btu/hr. [127 Mj/hr., 35.2 kW]] 2. Gas water heaters [400,000 Btu/hr. [422 Mj/hr., 117.2 kW] each] 3. Gas space heaters [70,000 Btu/hr. [79 Mj/hr., 20.5 kW] each] 4. Sediment traps, ...
Page 42 - High Altitude Orifice Sizing; Table 6
Gas Pipe Size Required for 1000 Btu Natural Gas — 0.64 Specific Gravity at 7 ± 1.5 inches [17.4 ± 4 mbar,1.74 ± 0.37 kPa] Water Column Pressure GasAp-pliancesTotalBtu/hr. Equivalent Length 25 feet[7.63 m] 50 feet[15.25 m] 75 feet[22.88 m] 100 feet[30.50 m] 125 feet[38.13 m] 150 feet[45.75 m] Based o...
Page 43 - Natural Gas
Model Gas Altitude Orifice NewRate feet [m] No. inches[mm] Quantity Part No. Btu/hr.*[Mj/hr.] 120L/N Natural Gas 2,001 – 4,000 [610 –1,220] 18 0.1695 [4.3] 3 M402988 248,400[262] 4,001 – 6,000 [1,221 –1,830] 19 0.1660 [4.2] M402995 226,800[239] 6,001 – 8,000 [1,831 –2,440] 21 0.1590 [4] M402992 205,...
Page 45 - • Close gas shut-off valve to gas tumble dryer be-; Wiring Diagram; The wiring diagram is located in the junction or contactor box.; Grounding Instructions; tumble dryer ground screw does not constitute a ground.
Electrical Requirements Electrical Requirements WARNING To reduce the risk of electric shock, fire, explosion,serious injury or death:• Disconnect electric power to the tumble dryer be- fore servicing. • Close gas shut-off valve to gas tumble dryer be- fore servicing. • Close steam valve to steam tu...
Page 46 - For CE Models Only; Junction Box
WARNING To reduce the risk of electrical shock, de-energizethe electrical circuit being connected to the tumbledryer before making any electrical connections. Allelectrical connections should be made by a qualifiedelectrician. Never attempt to connect a live circuit. W409R1 CAUTION Label all wires p...
Page 47 - To Connect Electrical Service To The
Ground and Terminal Block Locations for CE Gas and Steam Models TMB2247N_SVG 2 1 3 4 5 1. Earth/Ground 2. Junction Box 3. Terminal Block 4. Power Disconnect (Models Through 7/31/11) 5. Electrical Service Figure 18 Ground and Terminal Block Locations for Electric Models TMB2337N_SVG 1 4 2 3 1. Termin...
Page 48 - Jumper Configuration Instructions; • You have 400 – 415 Volt service and are connecting a model; Ferrite Ring Installation; be installed inside the contactor box. Refer to
2. Connect the conduit-encased leads to the disconnect switch,or circuit breaker. Connect the wire leads to the appropriatelabeled terminal on the terminal block. The ground wire mustbe connected to the ground connection as shown in Figure 17 , Figure 18 or Figure 19 . 3. Check the electrical servic...
Page 49 - CE Models; Ferrite Ring; Electrical Specifications; NOTE: Connect to individual branch circuit.
Non-CE Models TMB2270N_SVG 2 1 CE Models TMB2271N_SVG 2 1 3 1. Ferrite Ring 2. Junction Box 3. Models Through 7/31/11 Figure 20 Electrical Specifications NOTE: Minimum wire sizes are obtained from CanadianElectrical Code and are intended for use as a guidelineonly. Electrical connections should be m...
Page 52 - Steam Requirements
Steam Requirements Steam Requirements NOTE: Machines require a constant 80 to 100 psig [5.3to 6.9 bar] steam service for optimum operation. Themaximum allowable steam pressure for use with 50Hertz tumble dryers is 125 psig [8.6 bar]. In no casemay the pressure exceed the above value. Obtain specific...
Page 53 - 20 Series Tumble Dryers; Table 7; Minimum Supply Pipe Diameter
120 Series Tumble Dryers TMB2014N_SVG 7 6 6 3 5 12 13 1 2 11 8 10 9 4 NOTE: Refer to Table 7 for sizing of steam lines. Piping must also be sized accordingly for length of runs and number of elbows. 1. Supply 2. 12 in. [305 mm] Riser 3. Shut-Off Valve 4. Condensate Return Line from Supply Line 5. Re...
Page 55 - Table 8; Piping Recommendations; Installing Steam Trap and Making Con-
Steam Pressure PSI [ bar] Minimum Supply Pipe Diameter Steam Trap Size* Pounds Condensate/Hour [Kilo-grams Condensate/Hour] 80-100 [5.3-6.9] 1-1/4 in. NPT 517 [235] * Based on 6.9 bar. Table 8 Piping Recommendations • Trap each steam coil individually. Always keep the trap clean and in good working ...
Page 56 - Operating Instructions; similarly textured rubberlike materials.; Emergency Stop Button On CE Models; Figure; Operating Instructions; b. Close panel tightly against tumble dryer frame and lock
Operating Instructions Operating Instructions WARNING To reduce the risk of fire:• DO NOT DRY articles containing foam rubber or similarly textured rubberlike materials. • DO NOT DRY plastics, anything containing wax or chemicals such as mops and cleaning cloths, oranything dry-cleaned at home with ...
Page 57 - Reversing Operation; Dual Digital Timer Control; RQ Control Suffix; HIGH
b. Close loading door. Tumble dryer will not operate with the door open. 3. Determine Control Type and Temperature Settinga. Refer to the various controls and follow the instructions for the appropriate control type. b. The type of fabric being dried will determine the tempera- ture setting. Consult...
Page 58 - Error Codes; Table 9; Electronic OPL Micro Control
IMPORTANT: To stop the tumble dryer at any timeduring the cycle, OPEN DOOR. If the loading door orlint panel door is opened during the cycle, the heat-ing system will shut off and the motor will stop. Torestart the cycle, both doors must be closed and theSTART button must be pressed in. If the load ...
Page 59 - Press START pad to start tumble dryer.; LED OPL Control; RE Control Suffix
HIGH Temperature 180°F [82°C] MEDIUM Temperature 160°F [ 71°C] MED LOW Temperature 140°F [60°C] LOW Temperature 120°F [49°C] To use a Time Dry or Custom Cycle, refer to the ProgrammingManual. TMB1483N_SVG Figure 29 NOTE: Do not press directly on lights or the centerof pad. For proper selection, pres...
Page 60 - UniLinc Control; RU Control Suffix
S Models TMB1345R_SVG H Models TMB1346R_SVG Figure 34 U Models TMB1371R_SVG Y Models TMB2370N_SVG START STOP BACK Figure 35 C, D, and I Models TMB1375R_SVG Figure 36 UniLinc Control RU Control Suffix Operating Instructions 60 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Part N...
Page 61 - pad; DX4 OPL Control
1. Press the or keypad to change cycles. The center high- lighted position is the selected cycle.To customize a cycle, refer to the Programming Manual. 2. Press START to start selected cycle. IMPORTANT: If the loading door or lint panel door isopened during the cycle, the heating system willshut off...
Page 62 - Diagnostic Microprocessor Control
WARNING To prevent the risk of fire, remove laundry imme-diately in case of power failure. W779 Diagnostic Microprocessor Control General Operation The Diagnostic Microprocessor Control (DMP) is designed tomanage the drying and cooling cycles of the tumble dryer. Thecontroller is also programmed fro...
Page 64 - Ignition Control Operation and Trouble-; Fault Conditions
Function OPL Coin 7 Safety Tumble (OPL) or CoinCount/Pay (Coin) ON OFF #1 #7 DIP SWITCH OFF ON SAFETY TUMBLE OFF OFF NO SAFETY TUM-BLE ON ON COIN COUNT ON OFF PAY 8 Programming OFF OFF Disable=Off; Enable=On DIP Switch Functions Explained 1. Tumble dryer Type: This DIP switch selects the type of tum...
Page 66 - Troubleshooting Guide; Reset failure; Proper Electrode Location; Ignition Control Operation for Non-CE
Troubleshooting Guide Reset failure 1. Reset switch was pressed too long. Try to reset again. 2. Reset switch is shorted. Replace switch. Proper Electrode Location Proper location of the electrode assembly is important for optimalsystem performance. The electrode assembly should be locatedso that th...
Page 67 - System Tests; Low Voltage Detection test is disabled during Run Mode.; LED Color; Initialization
Lockout Mode. If no faults are detected, the Diagnostic LED willturn Green and the ignition control will enter Standby Mode. Standby Mode While in Standby Mode, the ignition control will continuallymonitor the system for faults. Once 24VAC is applied to termi-nals TH and GND on the control, the igni...
Page 69 - Adjustments; Gas Burner Air Shutter
Adjustments Adjustments WARNING To reduce the risk of electric shock, fire, explosion,serious injury or death:• Disconnect electric power to the tumble dryer be- fore servicing. • Close gas shut-off valve to gas tumble dryer be- fore servicing. • Close steam valve to steam tumble dryer before servic...
Page 70 - Airflow Switch; Loading Door Switch
T464I_SVG 1 4 2 4 3 4 1. Proper Airflow 2. Insufficient Airflow 3. No Airflow 4. Air Shutter Adjusting Screw Figure 43 Airflow Switch The airflow switch is set at the factory for proper operation. Noadjustment necessary. The airflow switch operation may be affected by shipping tapestill in place, la...
Page 71 - Belt Drive
Loading Door Strike (200 Series Mod- els) The loading door strike must be adjusted to have sufficient ten-sion to hold loading door closed against force of load tumblingagainst it. Proper adjustment is when 8-15 pounds [35.6-66.7 N]pull is required to open door.If adjustment is required, refer to Fi...
Page 72 - Daily; Monthly; Models equipped with a fire suppression system:
Maintenance Daily 1. Inspect the area surrounding tumble dryers, remove all com-bustible materials, including lint, before operating the ma-chines. 2. Check cylinder for foreign objects to avoid damage to cloth-ing and equipment. 3. Clean lint from lint compartment and screen to maintain prop-er air...
Page 73 - Machines equipped with a fire suppression system:; Annually; CAUTION; Table
8. Inspect cabinet and inner panels for any damage, replace orrepair as needed. 9. Clean burner tubes and orifice area of any lint buildup. 10. Machines equipped with a fire suppression system: All in- let and outlet hoses should be checked for any visible signs ofdeterioration. Replace as necessary...
Page 75 - Won’t Start
Before You Call for Service Won’t Start Won’t Heat Clothes Not Dry Possible Reason – Corrective Actions • Insert correct coin(s) or valid card if applicable. • Close the loading door tightly. • Close lint panel tightly. • Press the PUSH-TO-START or START pad/button. • Be sure power cord is plugged a...
