Agilent Agilent 6031A - Manual

Agilent Agilent 6031A

Agilent Agilent 6031A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
69 Page 69
70 Page 70
71 Page 71
72 Page 72
73 Page 73
74 Page 74
75 Page 75
76 Page 76
77 Page 77
78 Page 78
79 Page 79
80 Page 80
81 Page 81
82 Page 82
83 Page 83
84 Page 84
85 Page 85
86 Page 86
87 Page 87
88 Page 88
89 Page 89
90 Page 90
91 Page 91
92 Page 92
93 Page 93
94 Page 94
95 Page 95
96 Page 96
97 Page 97
98 Page 98
99 Page 99
100 Page 100
101 Page 101
102 Page 102
103 Page 103
104 Page 104
105 Page 105
106 Page 106
107 Page 107
108 Page 108
109 Page 109
110 Page 110
111 Page 111
112 Page 112
113 Page 113
114 Page 114
115 Page 115
116 Page 116
117 Page 117
118 Page 118
119 Page 119
120 Page 120
121 Page 121
122 Page 122
123 Page 123
124 Page 124
125 Page 125
126 Page 126
127 Page 127
128 Page 128
129 Page 129
Page: / 129

Table of Contents:

  • Page 3 – Safety Summary; Any LEDs used in this product are Class 1 LEDs as per IEC 825-1.
  • Page 5 – Declaration Page; DECLARATION OF CONFORMITY; Agilent Technologies
  • Page 6 – Acoustic Noise Statement; Herstellerbescheinigung
  • Page 7 – Table Of Contents; General Information
  • Page 11 – Introduction
  • Page 12 – Safety Considerations; Option; Accessories; Agilent Part No
  • Page 13 – Rack slide kit, non tilting; Instrument and Manual Identification
  • Page 14 – GP-IB Interconnection Cables and Connectors; Model; Ordering Additional Manuals
  • Page 15 – Related Documents
  • Page 16 – Agilent Technologies Model
  • Page 19 – Agilent Model
  • Page 21 – Installation; Mechanical Check; Preparation For Use; Location and Cooling
  • Page 22 – Bench Operation
  • Page 24 – Note; and recalibrate the power supply may result in damage to the unit.
  • Page 26 – Figure 2-3. Line Voltage Conversion Components
  • Page 27 – AC Line Impedance Check; Item
  • Page 29 – Operating Instructions; OPERATING INSTRUCTIONS
  • Page 30 – switches on the rear panel; while the unit is turned on; . Do not cause an electrostatic discharge into these; Controls and Indicators
  • Page 31 – Number
  • Page 33 – NOTE
  • Page 35 – Initial Setup and Interconnections; hazardous voltage.
  • Page 36 – current x resistivity; Table 3-2. Maximum Wire Lengths To Limit Voltage Drops
  • Page 37 – Wire Size
  • Page 38 – Figure 3-5. Connecting a Bypass Capacitor
  • Page 39 – Foldback Protection
  • Page 41 – Mode
  • Page 42 – Monitor Signals
  • Page 43 – Local Operation; Constant Voltage Operation
  • Page 44 – Constant Current Operation; Interface Functions
  • Page 45 – Multiline Message Control Functions
  • Page 46 – Device Clear; GP-IB Address Selection
  • Page 47 – Power-On Service Request; Initial Conditions
  • Page 48 – Programming Syntax; Numbers Sent to Power Supply
  • Page 49 – Numbers Returned To Controller
  • Page 50 – Command
  • Page 55 – Table 3-8. Format of Numbers Sent from Power Supply
  • Page 56 – Current Setting
  • Page 57 – Soft Limits
  • Page 59 – Hold and Trigger
  • Page 60 – Status Register
  • Page 62 – or
  • Page 64 – Description
  • Page 65 – TEST x; Analog Programming; The common terminal (; C and a power rating of at least 1/2 watt.
  • Page 66 – Constant Voltage Output, Resistance Control; If the programming terminals (VP to
  • Page 67 – Figure 3-10. Voltage Programming of Output Voltage; Multiple-Supply Operation; Figure 3-11. Optional Voltage Divide for Program Source
  • Page 68 – Figure 3-12. Resistance Programming of Output Current
  • Page 69 – Setting Voltage and Current; Series Operation
  • Page 70 – The RI bit in the status and astatus registers is set true (1).
  • Page 72 – Figure 3-19a. FLT and INH with Multiple Supplies
  • Page 77 – Blank Front Panel Option 001
  • Page 80 – Standard Commands for Programmable Instruments (SCPI); ABOUT THIS APPENDIX; The following documents will assist you with programming in SCPI; Beginner’s Guide to SCPI; These are two formal documents concerning the GP-IB interface:
  • Page 81 – Recommended; INTRODUCTION
  • Page 82 – LINKED CONNECTIONS; Figure C-1 Linked Connections
  • Page 83 – is
  • Page 84 – LANGUAGE DICTIONARY; Keywords; Common; Subsystem Commands
  • Page 85 – Figure C-2. Common Command Syntax Diagram
  • Page 86 – Meaning and Type; Clear Status; not; Command Syntax; Event Status Enable
  • Page 87 – Event Status Register; Identification; Operation Complete
  • Page 88 – Pending operations; Query Syntax; Power-on Status Clear
  • Page 89 – Recall
  • Page 90 – Reset; OUTP OFF; SAVE
  • Page 91 – Service Request Enable; Device Interface; Status Byte; Device Status
  • Page 92 – ABOR
  • Page 93 – Current Subsystem
  • Page 94 – Initiate Subsystem; Measure Subsystem
  • Page 96 – Status Subsystem; Status Operation Registers
  • Page 97 – Status Questionable Registers
  • Page 99 – Syntax is the same, regardless of the present language
  • Page 100 – Trigger Subsystem; BUS; Voltage Subsystem
  • Page 101 – STATUS REPORTING; IEEE 488.2 Standard Digital
  • Page 102 – Status Programming Examples.; Register Programming.
  • Page 103 – Figure C-4. Power Supply Status Structure
  • Page 104 – Status Programming Example.
  • Page 105 – Standard Digital Interface for Programmable Instrumentation.; Clearing the Status Byte Register.; Service Request Enable Register; Register Programming; Program Command
  • Page 106 – Status Programming Examples; Enables all bits to generate seruice requests; Output Queue; Standard Event Status Register Error Bits
  • Page 107 – Hardware Errors During Operation.
  • Page 108 – Error Number
  • Page 111 – Programming the Agilent 603xA Power Supplies Using Basic
  • Page 112 – Voltage and Current Readback
  • Page 114 – Output Inhibit / Enable; Condition; Present Status
  • Page 115 – Accumulated Status
  • Page 116 – Fault and Mask Registers
  • Page 117 – RQS; Bit position; Where
  • Page 118 – Service Request
  • Page 119 – Delay Time; The possible codes returned are:
  • Page 121 – Protection Functions; Overvoltage
  • Page 122 – Advanced Topics; Hold Mode
  • Page 125 – Index
  • Page 128 – Agilent Sales and Support Office 133; Agilent Sales and Support Office
  • Page 129 – Manual Updates
Loading the manual

OPERATING MANUAL

AGILENT 603xA FAMILY

AUTORANGING SYSTEM DC

POWER SUPPLIES

AGILENT Part No. 5959-3342

* OPERATING MANUAL FOR MODELS

Agilent 6030A, Serials 2934A-01825 to 01829

3023A-01925 and above

Agilent 6031A, Serials 2934A-01821 to 01825

3026A-01921 and above

Agilent 6032A, Serials 3004A-05881 to 05885

3023A-06181 and above

Agilent 6033A, Serials 3004A-05092 to 05096

3024A-05272 and above

Agilent 6035A, Serials 3038A-00101 and above

Agilent 6038A, Serials 2933A-08856 to 08860

3025A-09316 and above

* For instruments with higher serial numbers, a change page may be included

Microfiche Part No. 5959-3343

Edition 1 Printed: September 1990
Edition 2 Printed: January 1992

Updated: February 2000

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Safety Summary; Any LEDs used in this product are Class 1 LEDs as per IEC 825-1.

3 Safety Summary The following general safety precautions must be observed during all phases of operation of this instrument. Failure to complywith these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, andintended use of the instrument...

Page 5 - Declaration Page; DECLARATION OF CONFORMITY; Agilent Technologies

5 Declaration Page DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Manufacturer’s Name: Agilent Technologies Manufacturer’s Address: 150 Green Pond RoadRockaway, New Jersey 07866U.S.A. declares that the Product Product Name: a) Single Output System Power Supplyb) Autoranging Pow...

Page 6 - Acoustic Noise Statement; Herstellerbescheinigung

6 Acoustic Noise Statement Herstellerbescheinigung Diese Information steht im Zusammenhang mit den Anforderungen derMaschinenlärminformationsverordnung vom 18 Januar 1991. * Schalldruckpegel Lp < 70 dB(A) * Am Arbeitsplatz * Normaler Betrieb * Nach DIN 45635T. 19 (Typprüfung) Manufacturer’s Decla...

Other Agilent Models

All Agilent Other