Agilent 5071A - Manual

Agilent 5071A

Agilent 5071A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
Page: / 56

Table of Contents:

  • Page 3 – SERIAL NUMBER PREFIX: 3249A and above
  • Page 6 – Title Page, Serial Number Prefix; Throughout The Entire Manual
  • Page 7 – iii; Preface; How to Use This Manual v; Operating and Programming; Getting Started 1-3; Contents
  • Page 8 – iv; Installation 1-10; Preparation for Use 1-10; Service; Performance Tests 2-2; Exchange Assemblies 2-19
  • Page 9 – Specifications; Supplemental Characteristics 3-2; Power Requirements 3-2; Available Accessories and Options 3-4
  • Page 11 – vii; How to Use This Manual; b. Text information explanation for
  • Page 12 – viii; Instruments Covered by This manual
  • Page 14 – Introduction; Clock Functions; pps output: There is one 1 pps output on the 5071A front panel.
  • Page 15 – Getting Started; Connectors; Rear-Panel Connections
  • Page 16 – 071A Rear Panel Connections; NOTE
  • Page 18 – Performing Basic Tasks; Synchronizing to an External 1 PPS Reference
  • Page 19 – Monitoring Status
  • Page 20 – In Case of Difficulty; Front-Panel Indicators and Messages; Operating System Failure
  • Page 21 – SCPI Subsystem Commands; Status Reporting; Rear-Panel Status Output Operation; Status Output Programming
  • Page 23 – Installation; Preparation for Use; Power Requirements; nd paragraph, 1st and 2nd sentences are changed:; Bench Operation; Operating the 5071A From External Dc Power
  • Page 24 – Preparing the RP 5071-A For External-Dc Operation; Internal Standby Battery Maintenance
  • Page 25 – Assembly-Level Service
  • Page 26 – Performance Tests; 071A Operational Verification; Rear-Panel Output Signal Checks; and has an additional sentence:
  • Page 27 – Assembly Identification and Location; eight different telecommunications options:; TCO Option
  • Page 28 – Top-Level Diagnostic Tree Organization; Warning Message Diagnostic Tree (Diagnostic Subsection 4)
  • Page 29 – Warm-up and Fatal Error Diagnostic Tree
  • Page 34 – Theory of Operation; A1 Motherboard Circuit Description; Simplified Functional Description; Figure 3-1. 5071 A Simplified Block Diagram
  • Page 35 – Functional Block Descriptions; Figure 3-2. 5071 A Overall Block Diagram
  • Page 36 – The A8 1 PPS Assembly has the following input/output changes:; Instrument Control Block; Operating Firmware: Warning Mode
  • Page 37 – Signal Name; The third paragraph on page 3-21 that describes A8 is changed:
  • Page 38 – Power Supply Block; The first sentence of the first paragraph at the top of page 3-22 is
  • Page 39 – Table 3-6. Power Supply Block Interconnections; The following signal name information in table 3-6 on page 3-23 is; Overvoltage Protection Circuit
  • Page 40 – A11 Power Steering Logic Assembly; The circuit diagram on page 3-26 is changed:
  • Page 41 – The slot/module interconnect diagram on page 3-28 is changed:; 8V Subpanel Assembly; Figure 2-1. DC Input 1 and 2 Power Steering Schematic (48V Subpanel
  • Page 42 – The Power Supply block diagram on page 3-30 is changed:; B1 Internal-Standby Battery
  • Page 43 – Replaceable Parts; Exchange Assemblies
  • Page 45 – BACKDATING
  • Page 48 – Supplemental Characteristics; Time Standard; Clock 1 PPS Outputs; All references to 1 PPS Outputs are singular.; Clock Synchronization; The 2nd sentence is changed:; Internal Standby Battery (Nominal Values); Power option is present.; Environmental
  • Page 49 – The following are changed:; Accessories Furnished; The dc input connector description is changed:
  • Page 50 – Available Accessories and Options; Options
  • Page 51 – Service and Support
  • Page 53 – DECLARATION OF CONFORMITY
Loading the manual

$JLOHQW $3ULPDU\)UHTXHQF\6WDQGDUG

7HOHFRPPXQLFDWLRQV2SWLRQV

7HOHFRPPXQLFDWLRQV

2SWLRQV6XSSOHPHQWDO

0DQXDO

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - SERIAL NUMBER PREFIX: 3249A and above

Agilent 5071A Primary Frequency Standard Telecommunications Options Supplemental Manual This manual describes the Telecommunications options for the Agilent 5071A Primary Frequency Standard. The information in this manual applies toinstruments with one or more telecommunications options having the n...

Page 6 - Title Page, Serial Number Prefix; Throughout The Entire Manual

LIST OF EFFECTIVE PAGES SERIAL PREFIX, SERIAL #OR DATE CODE PAGES (05071-90042, December 2000) # All Serials ....................... 3-3. All Serials ....................... All pages. MANUAL CHANGES AGILENT 5071A TELECOMMUNICATIONS OPTIONS SUPPLEMENTAL MANUAL SERIAL PREFIX, SERIAL #OR DATE CODE CHA...

Page 7 - iii; Preface; How to Use This Manual v; Operating and Programming; Getting Started 1-3; Contents

iii Preface How to Use This Manual v Instrument Identification v Instruments Covered by This Manual vi Manual Organization vi How to Order Manuals vi 1 Operating and Programming Introduction 1-2 Introducing the HP 5071A 1-2 HP 5071A Major Features 1-2 Operating The HP 5071A 1-2 Clock Functions 1-2 G...

Other Agilent Models

All Agilent Other