Page 3 - Contents
3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . ...
Page 4 - Important Safety Instructions
4 Important Safety Instructions These warnings are provided in the interests of your safety. Ensureyou fully understand them before installing or using the appliance.Your safety is of paramount importance. If you are unsure about themeaning of these warnings contact the Customer Care Departmentfor a...
Page 6 - Disposal; Appliance Packaging Information; Remove transport packaging
6 Disposal Appliance Packaging Information All materials are environmentally friendly! They can be dumped orburned at an incinerating plant without danger.About the materials: The plastics can be recycled and are identified asfollows:>PE< for polyethylene, e.g. the outer covering and the bags ...
Page 7 - Installation; Installation Location
7 You can remove any remnants of adhesive using white spirit. Remove all adhesive tape and packing pieces from the interior of the appliance. Installation Installation Location The appliance should be set up in a well ventilated, dry room.Energy use is affected by the ambient temperature.The applian...
Page 8 - Reversing the door
8 Reversing the door The side at which the door opens can be changed from the right side(as supplied) to the left side, if the installation site requires. Warning! When changing the side at which the door opens, remove plug from the mains. Left door opening: Remove the grid from the appliance by pul...
Page 10 - Building the appliance in under a worktop
10 Building the appliance in under a worktop The dimensions of the recessed installation area must correspond with those indicated in the figure. Remove covering and adjust the bracket locking nuts. Push the appliance into place. The plug socket necessary for connection of the appliance to the elect...
Page 13 - Fitting the plinth; Power supply
13 Fitting the plinth Important! For the efficient operation of the appliance, it is important that theoriginal ventilation grid is used.• For an opening height dimension A=820 mm and a plinth height dimension a=100 mm, the plinth may be fitted without adjustments. The same applies to an opening hei...
Page 14 - Electrical Connection
14 The mains cable may only be changed by a qualified electrician orcompetent person. If your appliance needs repairing, please contactyour local AEG Service Force Centre. Electrical Connection Any electrical work required to install this appliance should be carriedout by a qualified electrician or ...
Page 15 - Description of the appliance; View of the appliance; Prior to Initial Start–Up
15 Description of the appliance View of the appliance ➁ ➂ ➃ ➀ Freezer calender ➁ Control panel ➂ Drawer (only for storage) ➃ Drawer (for storage and freezing) ➄ Temperature display Prior to Initial Start–Up Please clean the appliance interior and all accessories prior to initial start-up (see sectio...
Page 16 - Operating and indicator panel
Operating and indicator panel Important! Only use the appliance when built-in! 1 Thermostat control knob 2 ON/OFF switch 3 Pilot light (green) 4 Warning light (red) 5 Fast freeze light (yellow) 6 Fast freeze button and to switch off the warning tone The appliance can be activated/deactivated by pres...
Page 17 - Warning system
17 – the minimum storage temperature is no longer being maintained (fault); – excessive amounts of fresh food are placed inside; or– if the appliance door is open for too long. Turn the thermostat control knob to the desired setting with the aid of a coin.The compressor starts and then runs automati...
Page 18 - Starting up and temperature regulation; Ice pack
Starting up and temperature regulation Turn the thermostat control knob (1) in the direction of “1”.The green light (3) and the red light (4) come on, the audible warning sounds (if fitted), and the refrigeration motor starts up.Additionally operate the fast-freeze switch (6).The yellow pilot light ...
Page 22 - Switching off the appliance; Cleaning and Care
22 Switching off the appliance To switch off the appliance, turn the thermostat control knob to posi-tion "0". If the appliance is not going to be used for an extended period: Remove all deep-frozen packages as well as ice-trays.Switch off the appliance by turning the temperature regulator t...
Page 23 - Magnetic door seal
Switch off the appliance and unplug it.Clean the appliance and the interior accessories with a cloth and lukewarm water. Commercially available dish washing detergents may also be used.After cleaning wipe with fresh water and rub dry.After everything is dry, switch to fast freeze. After running the ...
Page 24 - Energy Saving Tips; Correcting Malfunctions
24 Energy Saving Tips • Do not install the appliance near boilers, radiators or other sources of heat. High ambient temperatures cause longer, more frequent operation of the compressor. • Ensure sufficient air circulation and exhaust at the appliance base and at the back wall of the appliance. Never...
Page 27 - Customer Care
27 Service & Spare Parts In the event of your appliance requiring service, or if you wish to pur-chase spare parts, contact your local AEG Service Force Centre bytelephoning: 08705 929929 Your call will be automatically routed to the Service Force Centre cov-ering your post code area. In guarant...
Page 28 - Noises during Operation
Noises during Operation The following noises are characteristic of refrigeration appliances:• Clicks Whenever the compressor switches on or off, a click can be heard. • Humming As soon as the compressor is in operation, you can hear it humming. • Bubbling/Splashing When refrigerant flows into thin t...
