AEG LAVW1010-W- User Manual

Page 2 - Contents

14 Contents Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Appliance Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Front and Side Views . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - Important Safety Information

15 1 Important Safety Information The safety of AEG appliances is in accordance with recognised techno-logical standards and appliance safety legislation. We nevertheless feel that it is important to acquaint you with the following safety guide-lines. • This appliance is heavy, care should be taken ...

Page 4 - Appliance Dimensions; Front and Side Views; Appliances with cold water connection only

16 Appliance Dimensions Front and Side Views Rear View Appliances with cold water connection only 598 575 592 950 10 0 50 850 +1 0 -5 10 +1 0 -5

Page 5 - Appliances with hot and cold water connections; Appliance Installation; Appliance Transit

17 Appliances with hot and cold water connections Appliance Installation 3 The appliance worktop must not be removed to gain a height reduction when installing under a kitchen worktop. Appliance Transit • To prevent electrical components becoming wet when moving the appliance, do not tip the washing...

Page 6 - Removing Transit Packaging

Appliance Installation 18 Removing Transit Packaging • Ensure all transit packaging is removed prior to installation. • Retain transit packaging for future use. 3 The appliance is supplied with a spanner (H) and plastic caps (E) (2 pcs.) and (G) (1 pc). 0 Remove the hose holder (A). 0 Remove the 2 s...

Page 7 - Installation-Site Preparation; Levelling the Appliance

Appliance Installation 19 Installation-Site Preparation • The installation surface must be clean, dry and level. • Do not install on deep pile carpet. • If the appliance ist installed next to heat source (e. g. cooking appliance), a heat insulating pad (85 x 57 cm) must be placed between the washing...

Page 8 - Electrical Connection

20 Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. 1 WARNING - THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. Before switching on,...

Page 9 - Permanent connection

Electrical Connection 21 • The wire coloured green and yellow must be connected to the terminal marked with the letter “E“ or by the earth symbol or coloured green and yellow. • The wire coloured blue must be connected to the terminal “N“ or coloured black. • The wire coloured brown must be connecte...

Page 10 - Water Connection; Water Pressure; Inlet Hose Connection

22 Water Connection 3 The washing machine is provided with safety devices preventing back-contamination of the water supply and complies with local water authority requirements. This appliance is designed to be permanently plumbed into your home’s water supply. Before connecting up the machine to ne...

Page 12 - Appliances with hot and cold water fill

Water Connection 24 Appliances with hot and cold water fill Washing machines with hot and cold fill should be connected as shown below. WARNING: The incoming hot water temperature must not exceed 70 °C. If only a cold water supply is available, connect the two hoses to the cold water outlet by means...

Page 13 - Water Drainage

Water Connection 25 Water Drainage The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic “U-Piece“ supplied, with an internal diameter of approximately 38 mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe...

Page 14 - AEG Service Force

26 AEG Service Force If you wish to contact your local AEG Service Force Centre for advice or spare parts, telephone: 0990 234234