Page 2 - SERVICE; General information and tips; CONTENTS
SERVICE When contacting Service, ensure thatyou have the following data available.The information can be found on therating plate. ModelPNCSerial Number The following symbols are used in thisuser manual: Warning - Important Safety information. General information and tips Environmental information S...
Page 4 - SAFETY INFORMATION
SAFETY INFORMATION Before the installation and use, readthis manual carefully:• For your safety and the safety of your property • To help the environment• For the correct operation of the ap- pliance. Always keep these instructions with theappliance also if you move or give it toa different person.T...
Page 5 - ENVIRONMENT CONCERNS; PACKAGING MATERIALS
internal components and cause leak-ages or malfunctions. • Do not install and connect a dam- aged appliance. • Make sure to remove all packaging and transport bolts. • Make sure that the mains plug is dis- connected from the mains socketduring installation. • Only a qualified person must do the elec...
Page 6 - PRODUCT DESCRIPTION
• To use the correct quantity of the de- tergent, check the water hardness ofyour domestic system The symbol on the product or on its packaging indicates that this productmay not be treated as householdwaste. Instead it should be taken to theappropriate collection point for therecycling of electrica...
Page 7 - ACCESSORIES; Spanner; CONTROL PANEL; PROGRAMME KNOB
ACCESSORIES 1 2 3 4 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear sideof the cabinet after the removal ofthe transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on theedge of a sink. CONTROL PANEL Ko...
Page 8 - DISPLAY; If the programme is completed but the symbol stays on:
DISPLAY 3 A B C D The display shows: A • The maximum temperature of the programme. B • The default spin speed of the programme.• 'No Spin' 1) and 'Rinse Hold' symbols. C • The display symbols. 2) Symbols Description Washing phase Rinse phases Spin phase Child lock You cannot open the appliance door ...
Page 10 - PROGRAMMES
Spin phase is off. 'Rinse Hold' function ison. TEMPERATURE BUTTON 10 Press button 10 to change the default temperature. - - = cold water ACOUSTIC SIGNALS FUNCTION You can hear the acoustic signals when:• You activate the appliance.• You deactivate the appliance.• You press the buttons.• The programm...
Page 13 - CONSUMPTION VALUES; Programmes for energy saving; BEFORE FIRST USE
CONSUMPTION VALUES Programme 1) Energy consumption (KWh) 2) Water consump- tion (litre) 2) White Cottons 95 °C 2.4 73 Cottons 60 °C 1.5 69 Cottons 40 °C 0.90 69 Synthetics 40 °C 0.55 48 Delicates 40 °C 0.65 58 Wool/ Handwash 30 °C 0.35 57 Programmes for energy saving Cotton 60 °C economy 3) 0.91 49 ...
Page 14 - USING THE DETERGENT AND ADDITIVES; This is the maximum level for the quantity of liquid additives.
2. Put the laundry in the drum, oneitem at a time. Shake the items be-fore you put them in the appliance. Make sure not to put too muchlaundry in the drum. 3. Close the door. Make sure that no laundry stays be-tween the seal and the door. There is arisk of water leakage or damage to thelaundry. USIN...
Page 15 - Check the position of the flap; – Do not use gelatinous or thick
Always obey the instructions that you find on the packaging of the deter-gent products. Check the position of the flap 1. Pull out the detergent dispenser un-til it stops. 2. Press the lever down to remove thedispenser. 3. To use powder detergent, turn theflap up. 4. To use liquid detergent, turn th...
Page 16 - SETTING AND STARTING A PROGRAMME; Steam
SETTING AND STARTING A PROGRAMME 1. Turn the programme knob. The re-lated programme indicator comeson. 2. The indicator of button 4 flashes with red colour. 3. The display shows the default tem-perature and spin speed. To changethe temperature and/or the spinspeed, press the related buttons. 4. Set ...
Page 17 - THE LAUNDRY LOAD
If you deactivate the appliance,it is necessary to set the pro-gramme again. AT THE END OF PROGRAMME • The appliance stops automatically.• The acoustic signals operate.• In the display comes on. • The indicator of the Start/Pause but- ton 4 goes off. • The door lock symbol goes off.• Press button 1 ...
Page 18 - Water hardness table; CARE AND CLEANING; DESCALING
STUBBORN STAINS For some stains, water and detergent isnot sufficient.We recommend that you remove thesestains before you put the items in theappliance.Special stain removers are available.Use the special stain remover that is ap-plicable to the type of stain and fabric. DETERGENTS AND ADDITIVES • O...
Page 19 - To clean the dispenser:
EXTERNAL CLEANING Clean the appliance only with soap andwarm water. Fully dry all the surfaces. CAUTION! Do not use alcohol, solvents orchemical products. MAINTENANCE WASH With the low temperature programmesit is possible that some detergent stays in the drum. Make regularly a mainte-nance wash. To ...
Page 20 - DRAIN PUMP; • The display shows an alarm code be-; To clean the drain pump:; Open the drain pump door.
3. Remove the top part of the liquidadditive compartment. 4. Clean all the parts with water. 5. Clean the dispenser recess with abrush. 6. Put back the dispenser in the recess. DRAIN PUMP Regularly examine the drainpump and make sure that it isclean. Clean the pump if:• The appliance does not drain ...
Page 21 - • The appliance fills with the water for
3. Put a container below the recess ofthe drain pump to collect the waterthat flows out. 4. Press the two levers and pull for-ward the drainage duct to let thewater flow out. 1 2 5. When the container is full of water,put the drainage duct back againand empty the container. Do steps 4and 5 again and...
Page 22 - To clean the water inlet filters:; EMERGENCY DRAIN; Remove the water inlet hose
To clean the water inlet filters: 1. Close the water tap. 2. Remove the water inlet hose fromthe water tap. 3. Clean the filter in the inlet hose witha stiff brush. 4. Remove the inlet hose behind theappliance. 5. Clean the filter in the valve with astiff brush or a towel. 45° 35° 6. Install again t...
Page 23 - TROUBLE SHOOTER AND SERVICE
TROUBLE SHOOTER AND SERVICE The start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the prob-lem (refer to the table). If not, contactthe service centre. With some problems, the acousticsignals operate and the displayshows an alarm code: • - The applia...
Page 25 - TECHNICAL DATA
Problem Possible cause Possible solution The appliance fillswith water anddrain immediately. The end of the drainhose is too low. Make sure that the drain hose isin the correct position. The washing re-sults are not satis-factory. The detergent you usedwas not sufficient or cor-rect. Increase the de...
Page 26 - INSTALLATION; UNPACKING
Maximum load Cotton 7 kg Spin speed Maximum 1400 rpm (L 75478 FL)1600 rpm (L 75678 FL) 1) Connect the water inlet hose to a water tap with a 3/4'' thread. INSTALLATION UNPACKING 1. Use the gloves. Remove the exter-nal film. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polys...
Page 28 - POSITIONING AND LEVELLING
10. Remove the three bolts. Use the keysupplied with the appliance. 11. Pull out the plastic spacers. 12. Replace the plastic spacers with theplastic caps. You can find these capsin the user manual bag. WARNING! Remove all the packaging andthe transit bolts before you in-stall the appliance. We reco...
Page 29 - • The appliance must be level and sta-; THE INLET HOSE; • Connect the hose to the appliance.
• The appliance must be level and sta- ble. CAUTION! Do not put cardboard, wood orequivalent materials below theappliance feet to adjust the lev-el. THE INLET HOSE 35 O 35 O 35 O 45 O 45 O 45 O • Connect the hose to the appliance. Turn the inlet hose only left or right.Loose the ring nut to set it i...
Page 30 - WATER DRAINAGE; With the plastic hose guide.
Water-stop device A The inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in the window «A» shows thisfault .If this occur, close the water tap andcontact the service centre to replacethe hose. WATER DRAINAGE There are differe...
Page 31 - Without the plastic hose guide.; • To a sink spigot.
Without the plastic hose guide. • To a sink spigot. Refer to the illustration. Put the drainhose in the spigot and tighten it witha clip. Make sure that the drain hosemakes a loop to prevent that remain-ing particles go in the appliance fromthe sink. • Directly to a built-in drain pipe in the room w...
