AEG F88089M0P/AU- User Manual

3. CONTROL PANEL 1 2 3 4 5 6 7 8 9 1 On/off button 2 Display 3 Delay touchpad 4 Program touchpad 5 ExtraHygiene touchpad 6 ÖKO PLUS touchpad 7 Multitab touchpad 8 RESET touchpad 9 Indicators Indicators Description Salt indicator. It is always off while the programme operates. Rinse aid indicator. It...

4. PROGRAMS Program Degree of soilType of load Programphases Options 1 1) AllCrockery, cutlery,pots and pans PrewashWash 45 °C or 70 °CRinsesDry ExtraHygieneÖKO PLUS 2 2) Heavy soilCrockery, cutlery,pots and pans PrewashWash 70 °CRinsesDry ÖKO PLUS 3 3) Normal soilCrockery and cut-lery PrewashWash 5...

6) With this program you can wash different loads with different soil. A higher temperature and water pressure in the lower basket, to wash items with heavy soil (e.g. pots andpans). A lower temperature and water pressure in the upper basket, to wash items withnormal soil (e.g. glassware). 7) Use th...

5. OPTIONS Activate or deactivate the op-tions before the start of a pro-gram. You cannot activate or de-activate the options while a pro-gram operates. If one or more options are set,make sure that the related indi-cators are on before the programstarts. 5.1 ExtraHygiene With this option you have b...

Acoustic signalson. Acoustic signalsoff. 4. Press ExtraHygiene to change the setting. 5. Press the on/off button to deactivatethe appliance and to confirm the set-ting. 5.5 How to set the colour of the TimeBeam It is possible to change the colour of theTimeBeam to match the colour of thekitchen floo...

Water hardness Water softener adjustment German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Manual Elec- tronic 19 - 22 33 - 39 3.3 - 3.9 23 - 27 2 1) 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 1 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 1 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 1 2 < 4 < 7 < 0...

6.2 Filling the salt container 1. Turn the cap counterclockwise andopen the salt container. 2. Put 1 litre of water in the salt con-tainer (only for the first time). 3. Fill the salt container with dishwash-er salt. 4. Remove the salt around the openingof the salt container. 5. Turn the cap clockwis...

7.1 Using the detergent 20 30 M A X 1 2 3 4 + - A B C 1. Press the release button ( B ) to open the lid ( C ). 2. Put the detergent in the compart-ment ( A ) . 3. If the program has a prewash phase,put a small quantity of detergent onthe inner part of the appliance door. 4. If you use detergent tabl...

1. Press the on/off button to deactivatethe appliance. 2. Close the water tap. If you do not press the on/offbutton, the AUTO OFF functionautomatically deactivates the ap-pliance a few minutes after theend of the program.This helps to decrease the ener-gy consumption, Important • For better drying r...

• Put the light items in the upper bas- ket. Make sure that they do not move. • Make sure that the spray arms can move freely before you start a pro-gram. 8.4 Before starting a program Make sure that: • The filters are clean and correctly in- stalled. • The spray arms are not clogged. • The position...

6. Make sure that the filter ( B ) is cor- rectly positioned under the 2 guides( C ). 7. Assemble the filter ( A ) and put it back in filter ( B ). Turn it clockwise until it locks. An incorrect position of the filterscan cause bad washing resultsand damage to the appliance. 9.2 Cleaning the spray a...

Problem Possible solution Make sure that the pressure of the watersupply is not too low. For this information,contact your local water authority. Make sure that the water tap is not clogged. Make sure that the filter in the inlet hose isnot clogged. Make sure that the inlet hose has no kinks orbends...

5. Press the on/off button to deactivatethe appliance and to confirm the set-ting. 6. Adjust the released quantity of rinseaid. 7. Fill the rinse aid dispenser. 11. TECHNICAL INFORMATION Dimensions Width / Height / Depth(mm) 596 / 818 - 878 / 580 Electrical connection Refer to the rating plate. Volt...

12. INSTALLATION If floor is not level, adjustlevelling legs to suit The hos e s hould not beextended by more than2 metres or water pump-out problems m a y occu r Remove entire plasticmembrane from sink trapspigot & fit drain hose to spigotwith clamp There should be a minimum2mm gap between the ...

12.2 Adjusting the height of the appliance 1. Remove the adjustable plinth. 2. – To lift the front of the appliance, turn the two front feet counter-clockwise. – To lift the rear of the appliance, turn the middle screw counter-clockwise. 12.3 Adjusting the level of the appliance A correct adjustment...

12.5 Custom made kick-panel (for integrated appliances and full-stainless-steel door appliances) We recommend that you make a custommade kick-panel that aligns your kitchencabinets.A notched continuous panel is necessaryto prevent door swing interference andto keep kick-panel alignment with adja-cen...

Make sure that the local water authoritygives you the average mains pressure inyour area. In order to pass the safety valve throughthe kitchen cabinets, an opening of atleast 45 mm x 90 mm is needed. Water drain hose The highest point of the drain hose mustbe no more than 600 mm from the floorand mu...

13. WARRANTY FOR SALES IN AUSTRALIA AND NEWZEALANDALL AEG BRANDED APPLIANCES This document sets out the terms andconditions of the product warrantiesfor AEG Appliances. It is an importantdocument. Please keep it with yourproof of purchase documents in a safeplace for future reference should yourequi...

ance is transported at the owner’scost and risk while in transit to andfrom AEG or its ASC. 6. Proof of purchase is required beforeyou can make a claim under this war-ranty. 7. You may not make a claim under thiswarranty unless the defect claimed isdue to faulty or defective parts orworkmanship. AEG...

Before calling for service, please ensure that the steps listed in point 13 above have been followed. SERVICE AUSTRALIA www.aeg.com/au FOR SERVICE or to find the address of your nearest state service centre in Australia PLEASE CALL 1300 363 664OR EMAIL [email protected] For the cost o...