AEG F77023MOP- User Manual

2. PRODUCT DESCRIPTION 1 2 3 4 5 6 9 11 7 8 13 10 12 1 Worktop 2 Top spray arm 3 Upper spray arm 4 Lower spray arm 5 Filters 6 Rating plate 7 Salt container 8 Water hardness dial 9 Rinse aid dispenser 10 Detergent dispenser 11 Cutlery basket 12 Lower basket 13 Upper basket 3. CONTROL PANEL 1 2 3 4 5...

1 On/off button 2 Program button 3 Programme indicators 4 Display 5 Delay button 6 Start button 7 Indicators 8 Option button Indicators Description Multitab indicator. ExtraHygiene indicator. Washing phase indicator. Rinsing phase indicator. Drying phase indicator. End indicator. Rinse aid indicator...

Programme Degree of soilType of load Programmephases Options 5) Normal soilCrockery and cut-lery PrewashWash 50 °CRinsesDry ExtraHygiene Normal soilCrockery and cut-lery Wash 55 °CRinses ExtraHygiene Normal or light soilDelicate crockeryand glassware Wash 45 °CRinsesDry 1) The appliance senses the d...

5. OPTIONS Activate or deactivate the op-tions before the start of a pro-gramme. You cannot activate ordeactivate the options while aprogramme operates. If one or more options are set,make sure that the related indi-cators are on before the pro-gramme starts. 5.1 Multitab Activate this option only w...

6.1 Adjusting the water softener Water hardness Water softener adjustment German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Manual Elec- tronic 51 - 70 91 - 125 9.1 - 12.5 64 - 88 2 1) 10 43 - 50 76 - 90 7.6 - 9.0 53 - 63 2 1) 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 2 1) 8 29 - 36 51 - 64 ...

6.2 Filling the salt container 1. Turn the cap counterclockwise andopen the salt container. 2. Put 1 litre of water in the salt con-tainer (only for the first time). 3. Fill the salt container with dishwash-er salt. 4. Remove the salt around the openingof the salt container. 5. Turn the cap clockwis...

7.1 Using the detergent 20 30 M A X 1 2 3 4 + - A B C 1. Press the release button ( B ) to open the lid ( C ). 2. Put the detergent in the compart-ment ( A ) . 3. If the programme has a prewashphase, put a small quantity of deter-gent on the inner part of the appli-ance door. 4. If you use detergent...

Cancelling the delay startwhile the countdown operates Press Delay again and again until: • The display shows the programme du- ration. • The phase indicators come on.• The programme starts. Cancelling the programme Press and hold Delay and Start at the same time until:• All the programme indicators...

• Make sure that the spray arms can move freely before you start a pro-gramme. 8.3 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products cancause damage to the appliance. • The rinse aid helps, during the last rinsing phase, to dry the dishes wit...

A1 A2 2. To disassemble the filter ( A ), pull apart ( A1 ) and ( A2 ). 3. Remove the filter ( B ). 4. Wash the filters with water. 5. Put the filter ( B ) to its initial position. Make sure that it assembles correct-ly under the two guides ( C ). 6. Assemble the filter ( A ) and put it in- to posit...

Problem Possible cause Possible solution You did not press Start . Press Start . The fuse in the fuse box isdamaged. Replace the fuse. The delay start is set. Cancel the delay start orwait for the end of thecountdown. The appliance doesnot fill with water. The water tap is closed. Open the water tap...

2. Make sure that the appliance is insetting mode. Refer to ‘SETTINGAND STARTING A PROGRAMME’. 3. Press and hold Delay and Start at the same time until the indicators ( A ), ( B ) and ( C ) flash. 4. Press Option . • The indicators ( A ) and ( C ) go off. • The indicator ( B ) continues to flash. • ...