AEG AREI2LF 4 - User Manual

AEG AREI2LF 4

AEG AREI2LF 4 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
Page: / 32

Table of Contents:

  • Page 5 – Figure 1: Concept of the reading system; Installation; transponder; reader with
  • Page 6 – Connecting of the plug; may be; Figure 2: Connecting of the plug
  • Page 8 – Assembling of the cable pipe; at the SAB Cab: central and at one side of the cab.; Mounting of the cable; The cable must be mounted in following steps:
  • Page 9 – Figure 4: Mounting for the cable
  • Page 10 – Pin assignment of the SAB connectors; Figure 5: Pin assignment of the SAB connectors
  • Page 11 – Figure 6: Pin assignment of the SAB connectors; Mounting of the external antenna / of the AMP 4 / AMP 8
  • Page 12 – BFH; Visual signal lamps; L2: lit, if the last reading process was successful
  • Page 13 – The protocol format is as follows; Command; Output format
  • Page 14 – Instruction specific output; GT; Output after changing a parameter; MD; Output at parameter query
  • Page 15 – Blank instuction; The instruction set isn’t case-sensitiv.; Linefeed
  • Page 16 – Instructions for the hardware settings; BD; EC – echo function; The command EC changes of the echo function setting.; EC; Echo inactive
  • Page 17 – CID – Suppression of ID Codes; only the first; No suppression
  • Page 18 – CN – Suppression of No Reads; CN
  • Page 19 – NID – Failure Protection; NID; TOR – Maximum reading time; TOR
  • Page 20 – Instructions for the memory settings; VER; VS – Show parameter; VS
  • Page 21 – VSAVE – Save parameter; VSAVE; RST – Warm start; The command RST causes a warm start of the reader.; Figure 7: Workflow RST; INIT – Warmstart with default parameters; This command starts the reader new with the default parameters.; INIT; RST
  • Page 22 – Operating Modes of the Reader; There are two operational modes defined:; MD 2 - Triggered by an Software Command; Figure 9: Software triggered reading operation
  • Page 23 – Figure 10: Software triggered reading operation with TOR>0; Please note; MD 0 - Continuous Reading; Figure 11: continuous operation
  • Page 24 – Startup and testing the reader
  • Page 25 – Wait for the answer; read block 20; RD; read all blocks from 16 to 33
  • Page 26 – Writing WD
  • Page 28 – Special Instructions for Using a Read / Write System; size of the antennas
  • Page 29 – Figure 12: Orientation between transponder and reader
  • Page 30 – Federal Communications Commissions (FCC) Statement
  • Page 32 – Revisions
Loading the manual







Compact Reader ARE i2-LF

Installation Guide
for Systems with a
Serial Interface RS 232

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Other Manuals for AEG AREI2LF 4

Summary

Page 5 - Figure 1: Concept of the reading system; Installation; transponder; reader with

--------------------------------------------------------------------------------5/32-------------------------------------------------------------------------------- Figure 1: Concept of the reading system 3 Installation To get the specified reading performance it is necessary to do the installation ...

Page 6 - Connecting of the plug; may be; Figure 2: Connecting of the plug

--------------------------------------------------------------------------------6/32-------------------------------------------------------------------------------- Attention! The topology of the ground wires must be done in the right way (according state of art). 3.2.1 Connecting of the plug Attent...

Page 8 - Assembling of the cable pipe; at the SAB Cab: central and at one side of the cab.; Mounting of the cable; The cable must be mounted in following steps:

--------------------------------------------------------------------------------8/32-------------------------------------------------------------------------------- Attention! The minimum voltage at the readers input mustn’t be lower then 9V. The maximum length of the serial RS232 cable is 15m. 3.3....

Other AEG Models

All AEG Other