AEG AREDT1HF 1 - User Manual

AEG AREDT1HF 1

AEG AREDT1HF 1 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
Page: / 45

Table of Contents:

  • Page 5 – Introduction; The main features of the reader are listed below:
  • Page 6 – Startup and testing the reader DT1; Connect the reader with the USB interface from your notebook or pc; AEG ID instruction set
  • Page 7 – Entering instuctions; The protocol format is as follows; Command; Output format; GT; Output after changing a parameter; MD
  • Page 8 – Output at parameter query; Blank instuction; ERROR CODE
  • Page 10 – Upper and lower case; The instruction set isn’t case-sensitiv.; Linefeed
  • Page 11 – HF – radio frequency; With the command HF you can switch the antenna field on and off.; PARAMETER; off; HID – human interface device/keyboard
  • Page 12 – KL – keyboard language; KL
  • Page 13 – RE – read EEPROM; RE; LED – LED control; LED
  • Page 14 – RST – reset; RST
  • Page 15 – WE – write EEPROM; Using the command WE you can write one byte to the internal EEPROM.; WE; address; PARAMETER 2; data; VER – version; With the command VER the reader sends the actual firmware version.; VER
  • Page 16 – CE; CID – suppression of ID Codes; only the first
  • Page 17 – CN – suppression of No Reads; CN
  • Page 18 – manual controlling; MC – mirror code; normal sequence
  • Page 19 – RA – resend last answer; The command RA resends the last answer sent by the reader.; RA; TSC – time show code; TSC; TSC is not active; TOR – maximum reading time; The time constant TB (time base) has always the default value 100ms.; TOR
  • Page 20 – SI – set iso standard; parameter; VSAVE – variables save; VSAVE; VS – variables show; VS
  • Page 21 – GA; GT – get tag
  • Page 22 – HD – halt detected code; HD; MD – mode of operation
  • Page 23 – RD – read page
  • Page 24 – RDM – read page manual
  • Page 25 – WD – write page
  • Page 26 – WDM – write page manual
  • Page 27 – use saved key 1 to 8; KT – key type
  • Page 29 – PDC – purse decrement
  • Page 30 – PIC – purse increment
  • Page 32 – RQ – request; RQ; SE – select; ACK; SE2 – select level 2
  • Page 33 – WK – write key; WK; key number; 2 characters
  • Page 34 – AFI – application family identifier; every transponder is read; BS – block size; GMS – get multiple block security; Input format one block:
  • Page 36 – LDS – lock DSFID; PARAMETER 1
  • Page 37 – characters; WA – write AFI; AFI; WDS – write DSFID; DSFID
  • Page 38 – ADDRESS; USER
  • Page 39 – Operating Modes of the Reader; MD 0 - continuous mode; MD 2 - Triggered by an software command; Figure 9: Software triggered reading operation
  • Page 40 – Figure 10: Software triggered reading operation with TOR>0; Please note; MD 0 - Continuous Reading; Figure 11: continuous operation
  • Page 41 – Instructions
  • Page 42 – FCC Information; Federal Communications Commissions (FCC) Statement; Reorient or relocate the receiving antenna.
  • Page 43 – Converting decimal to hexadecimal
Loading the manual







ARE DT1

Installation Guide

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 5 - Introduction; The main features of the reader are listed below:

--------------------------------------------------------------------------------5/45-------------------------------------------------------------------------------- 1 Introduction This document describes the RFID-reading device ARE DT1 and the set-up procedure. The main features of the reader are li...

Page 6 - Startup and testing the reader DT1; Connect the reader with the USB interface from your notebook or pc; AEG ID instruction set

--------------------------------------------------------------------------------6/45-------------------------------------------------------------------------------- 2 Startup and testing the reader DT1 • Connect the reader with the USB interface from your notebook or pc • In the device manager there...

Page 7 - Entering instuctions; The protocol format is as follows; Command; Output format; GT; Output after changing a parameter; MD

--------------------------------------------------------------------------------7/45-------------------------------------------------------------------------------- With the command CS you can change to the alternative instruction set. If the reader is set to alter-native instruction set, you can ch...

Other AEG Models

All AEG Other