Page 2 - Important Safety Information; Installation; Child Safety
2 Important Safety Information You MUST read these warnings carefully before installing or using the hob. Ifyou need assistance, contact our Customer Care Department on 08705 350350 Installation z This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to ...
Page 4 - Guide to Use the instructions; Contents; Instructions for the User
4 This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition. Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step ...
Page 5 - Description of the Hob; INSTALLATION; WHEN THE HOB IS FIRST INSTALLED
5 1. Hob Top 2. Semi-rapid Burners 3. Auxiliary Burner 4. Ultra-rapid Burner (triple crown) 5. Control knobs Description of the Hob INSTALLATION Any gas installation must be carried out by a registered CORGI installer, and in accordance with existing rules and regulations. The relevant instructions ...
Page 6 - Hob burners; Operation; Using the Wok Stand
6 Hob burners To light a burner: z Push in the relevant control knob and turn it to maximum position. z Upon ignition, keep the knob pushed down about 5 seconds . This will allow the "thermocouple" (fig. 1 - letter D) to be heated and the safety device to be switched off,otherwise the gas su...
Page 7 - Maintenance and Cleaning; The Hob Top
7 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easilythan if it is left to cool. The Hob Top Regularly wipe over the hob top us...
Page 8 - Something Not Working?; Ignition electrode
8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contactingyour local Service Force Centre. SYMPTOM There is no spark when lighting the gas The gas ring burns unevenly SOLUTION Check that the unit is plugged in and the electrical supply...
Page 10 - Guarantee Conditions; Standard guarantee conditions; Exclusions; European Guarantee
10 Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereofis proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair orreplace the same FREE O...
Page 11 - Engineers technical data; Supply Connections; Ignition HT Spark
11 Instructions for the Installer Engineers technical data B U R N E R ULTRA-RAPID SEMI-RAPID A U X I L I A R Y (triple crown) ( m e d i u m ) (small) POSITION M A X M I N M A X M I N M A X M I N NOMINAL THERMALPOWER (kW) 3.8 1.20 1.9 0.45 1.0 0.33 NOMINAL FLOWRATE (m 3 /h) 0.362 0.114 0.181 0.043 0...
Page 12 - Important safety requirements; Location
12 700 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 700 mm 400 mm 100 mm 400 mm 50 mm 50 mm 55 mm CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE FO 2028* FO 2027* Important safety requirements This hob must ...
Page 13 - Gas Connection
13 Installation Important This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI registered installer. The manufacturer will not accept liability, should the above instructions or any of theother safety instructions in...
Page 14 - Cut Out Size; Building In; Building over a cupboard or drawer
14 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heatresistant board below the base of the hob on the underside of the work surface.It is also ...
Page 15 - Building over a kitchen unit with door
15 ON/OFF SWITCH FLEXOUTLET ON/OFF SWITCH FLEXOUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arrangements must be taken indesigning the furniture unit, in order to avoidany contact with the bottom of the hob whichcan be heated when it is operated. Therecommended solution is...
Page 16 - Fitting the hob to the worktop
16 Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the undersideoutside edge of the hob. It is essential that no gaps are left in this seal in order to preventspillage near the hob seeping into the cabinet below. 1) Remove the pan supports, ...
Page 17 - Electrical connections
17 Electrical connections Any electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accordance with the current regulations.THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.Th...
Page 18 - Permanent Connection; Wiring diagram; Replacement of the cable
18 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switchbetween the hob and the electricity supply (mains), with a minimum gap of 3 mm betweenthe switch contacts and of a type suitable for the required load in compliance with thecurrent ele...
Page 19 - Fault Finding; Preliminary Electrical Systems Check
19 Fault Finding Preliminary Electrical Systems Check START Isolate applianceand carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supplyshould now besatisfactory. Carry out: D: Resistance to Earth check. Inlet wiringfaulty.Rectify anyfault. Isolat...
Page 21 - Ignition System / Gas Ignition
21 Check gas supply atburner Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fitting ofburners Check position of theelectrode Check by pass simmeradjusted...
Page 22 - Commissioning; Pressure Testing
22 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite.2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several t...
Page 23 - Conversion from Natural Gas to LPG; Method; To adjust the gas rate
23 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can beconverted for use with butane or propane gas providing the correct injectors are fitted andthe gas rate is adjusted to suit. Method 1) Ensure that the gas taps are in the 'OFF...
