AEG 65852 G- User Manual

6 1. Hob Top2. Semi-rapid Burner3. Triple Crown Burner4. Auxiliary Burner5. Control knob for front left burner (semi-rapid)6. Control knob for back left burner (semi-rapid)7. Control knob for back right burner (triple crown)8. Control knob for front right burner (auxiliary) Description of the Hobs I...

7 Hob burners control knobs The symbols on the knobs mean that : # there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. To light a burner: # t u r n t h e r e l e v a n t k n o b a n ...

8 Burner minimum maximum diameter diameter Triple crown (ultra-rapid) 180 mm 260 mm Medium (semi-rapid)rear 120 mm 220 mm front 120 mm 180 mm Small (auxiliary) 80 mm 160 mm As soon as a liquid starts boiling, turn down the flame so that it willbarely keep the liquid simmering. Use only pans or pots ...

9 Using the Wok Stand A wok stand is provided to enable you to use a roundbottomed wok on the hob. The wok stand must onlybe used on the triple crown burner , and should not be used with any other type of wok or pan. Whenfitting the wok stand, ensure the recesses in the fra-me fit securely onto the ...

1 0 Before any maintenance or cleaning can be carried out, you mustDISCONNECT the hob from the electricity supply.The hob is best cleaned whilst it is still warm, as spillage can be removedmore easily than if it is left to cool.This appliance cannot be cleaned with steam or with a steam cleaningmach...

1 1 The Burners The burner caps and crowns can be removed for cleaning. Wash the burners caps and crowns using hot soapy water, and remove marks witha mild paste cleaner. A well moistened soap impregnated steel wool pad can beused with caution, if the marks are particularly difficult to remove. Afte...

1 2 Something Not Working? If the hob is not working correctly, please carry out the following checks beforecontacting your local Service Force Centre. SYMPTOM % There is no spark when lightingthe gas. % The gas ring burns unevenly. SOLUTION & Check that the unit is plugged inand the electrical ...

1 3 OVERALL DIMENSIONS Width: 594 mmDepth: 510 mm CUT OUT DIMENSIONS Width: 560 mmDepth: 480 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V ~ 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. HEAT INPUT Rear...

1 5 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations(Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas InstallationI.S....

1 6 C L E A R A N C E S R E Q U I R E D W H E N F I T T I N G T H E G A S H O B W I T H O U T A C O O K E R H O O D A B O V E FO 0813 FO 0812 Installation IMPORTANT This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registere...

1 7 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 It is important to install the elbow correctly, with the shoulder on the end of thethread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. Gas Connection Connection to the gas supply ...

1 8 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heatresistant board below the base of the hob on the underside of the work surface. It is als...

1 9 ON/OFF SWITCH FLEXOUTLET ON/OFF SWITCH FLEXOUTLET 1 2 Building over a kitchen unit with door Proper arrangements must be taken in designing thefurniture unit, in order to avoid any contact with thebottom of the hob which can be heated when it isoperated. The recommended solution is shown indiagr...

2 0 S e a l S e a l S e a l S e a l S e a l Fitting the Hob into the Worktop Carry out the building in of the hob asfollows: 1. place the seals supplied with the hob on the front edge of the cutout. Then, place them at 11 mmfrom the side edges and at 10m m f r o m t h e r e a r e d g e , a ss h o w ...

2 1 Electrical connections Any electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed....

2 2 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switchbetween the hob and the electricity supply (mains), with a minimum gap of 3 mm between theswitch contacts and of a type suitable for the required load in compliance with the currentel...

2 3 Fault Finding Preliminary Electrical Systems Check START Isolate applianceand carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supplyshould now besatisfactory. Carry out: D: Resistance to Earth check. Inlet wiringfaulty.Rectify anyfault. Isola...

2 4 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale andadjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts...

2 5 Check gas supply atburner Ignition System / Gas Ignition Y E S Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fittingof burners Check position of theelectrode Check by pass simmeradjus...

2 6 Commissioning When the hob has been fully installed it will be necessary to check the minimum flamesetting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several ...

2 7 Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion from natural gas to LPG should only be undertaken bya competent person. It is important to note that this model is designed for use with natural gas but can be convertedfor use with butane or propane gas providing the correc...

2 8 Guarantee/Customer Service Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the pur-chase this AEG-Electrolux appliance or any part thereof is proved to be defectiveby reason only of faulty workmanship or materials, we will, at our option repair...

3 0 This appliance is guaranteed by Electrolux in each of the countries listed at the back of this usermanual, for the period specified in the appliance guarantee or otherwise by law. If you movefrom one of these countries to another of the countries listed below the appliance guaranteewill move wit...