AEG 6130 V-ma- User Manual
AEG 6130 V-ma– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Product specification; Product Discontinued
- Page 3 – General; PANEL MOUNTING; Connection to
- Page 4 – Terminal block 1 - 20
- Page 5 – Typical wiring diagram (AS731 automatic mains fail generator)
- Page 6 – Communication ports; Communication networks; Modem Communications
BEFORE BEGINNING INSTALLATION OF THIS MURPHY PRODUCT
Disconnect all electrical power to the machine
Make sure the machine cannot operate during installation
Follow all safety warnings of the machine manufacturer
Read and follow all installation instructions
W A R N I N G
General
The Autostart AS731 and AS732 provide full-function,
automatic or manual control for diesel generators.
The fully programmable, microprocessor-based units
include full measurement and display of engine and AC
generator parameters, with a fully automatic fault protection
and warning system. Facilities are also provided for remote
monitoring and control via RS232 communication link and
PC software; the AS732 additionally features an RS485
MODBUS RTU compatible link.
This document details the panel mounting and electrical
connection of AS731 and AS732 units fitted with firmware
versions V1.00 through V2.x.x. Further details about
specification, programming and operation may be found
in the following documents:-
Doc. ref.
Title
ms6127 AS731
bulletin
ms6343 AS732
bulletin
mi6129
AS731/732 installation B: programming
mi6243
AS731/732 installation C:
AS730 to AS731/AS732 retrofitting
mi6130 AS731/732
operation
mi6131
AS731/732 and PC software model AS7CN
mi6344
AS732 RS485 MODBUS protocol
MODBUS® is a registered trademark of AEG Schneider Automation Inc.
Autostart AS731/AS732 Generator Controller
Installation Instructions
Section A: Panel Installation and Wiring
mi6128
revision G, 10
th
Sept 2007
catalogue section 75
Please read the following information before installing.
A v isual inspection of this product for damage during
shipping is recommended before installation. It is your responsibility to ensure that qualified mechanical and electrical
technicians install this product. If in doubt, please contact your local Murphy representativ e.
GENERAL INFORMATION
Front facia
1. 2 line x 16 character backlit liquid crystal display
2. Operator control keys
3. Auto/manual mode LED indication
Rear facia
4. Mounting clamps
5. 2 x two part, screw terminal blocks, 1 – 20 and 21 - 30
6. RS232 communication port (RJ11 connector)
7. (AS732 only) RS485 comms ports (2 x RJ45 connectors)
FRANK W. MURPHY LTD.
Church Rd, Laverstock,
Salisbury, SP1 1QZ, United Kingdom
tel:
+44 1722 410055
fax:
+44 1722 410088
email:
web:
www.fwmurphy.co.uk
FW MURPHY
PO Box 470248
Tulsa, Oklahoma 74147, USA
tel:
+1 918 317 4100
fax:
+1 918 317 4266
email:
web:
www.fwmurphy.com
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time.
MURPHY, the Murphy logo, are registered and/or common law trademarks of Murphy Industries, Inc. This document, including
textual matter and illustrations, is copyright protected by Frank W Murphy Ltd., with all rights reserved. © 2007 Frank W Murphy Ltd.
Product Discontinued
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
FWMurphy – AS731 / AS732 installation section A: panel installation and wiring mi6128 revision G 10 th Sept 2007 p2/6 Anti-static precautions The AS731/732 features sensitive electronic components that may be damaged by static discharge. Anti-static precautions must therefore be observed when storin...
FWMurphy – AS731 / AS732 installation section A: panel installation and wiring mi6128 revision G 10 th Sept 2007 p3/6 General Electrical connection is at the rear of each unit, through a pair of two-part type screw terminal blocks labelled 1 - 20 and 21 - 30. Use a 3mm (1/8”) flat head screwdriver t...
FWMurphy – AS731 / AS732 installation section A: panel installation and wiring mi6128 revision G 10 th Sept 2007 p4/6 A typical wiring diagram is shown in the panel on page 5. Specific terminal functions are as follows:- Terminal block 1 - 20 Pin Function 1 3 Negative DC power supply/ground Positive...
