Page 2 - Important Safety Information; Installation; Child Safety; ENGLISH
2 Important Safety Information You MUST read these warnings carefully before installing or using thehob. If you need assistance, contact our Customer Care Department on08705 350 350 Installation ● This hob must be installed by qualified personnel, according to themanufacturer’s instructions and to t...
Page 3 - Service
3 ● When in use a gas cooking hob will produce heat and moisture in theroom in which it has been installed. Ensure there is a continuous airsupply, keeping air vents in good condition or installing a cooker hoodwith a venting hose. ● When using the hob for a long period of time, the ventilation shou...
Page 4 - Contents
4 Contents Important Safety Information .................................................................... 2 Instructions for the User .............................................................................. 6 Description of the Hob ..............................................................
Page 5 - Guide to Use the instructions
5 This appliance is manufactured according tothe following EEC directives:73/23 EEC - 90/683 EEC - 93/68 EEC -89/336 EEC - 90/396 EEC,current edition. Guide to Use the instructions The following symbols will be found in the text to guide you throughout theInstructions: Safety Instructions Step by st...
Page 7 - HOB BURNERS; Operation
7 HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to themaximum position ( ), then push it down to ignite the burner. Upon, ignition, adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and tryagain. When switching on the mains, aft...
Page 8 - Maintenance and Cleaning
8 Before any maintenance or cleaning can be carried out, you mustDISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can beremoved more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrun...
Page 9 - Something Not Working?
9 Something Not Working? If the hob is not working correctly, please carry out the following checksbefore contacting your local AEG Service Force Centre. SYMPTOM ■ There is no spark when lightingthe gas ■ The gas ring burns unevenly SOLUTION ◆ Check that the unit is plugged inand the electrical supp...
Page 10 - Service and Spare Parts; CUSTOMER CARE
10 Service and Spare Parts When you contact the Service Centre, they will need the followinginformation: 1. Your name, address and post code. 2. Your telephone number 3. Clear and concise details of the fault 4. The model and the serial number (see rating label on the back of this instruction bookle...
Page 11 - Guarantee Conditions
11 Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similardocumentation.The guarantee doe...
Page 12 - Instructions for the Installer; Engineers technical data
12 OVERALL DIMENSIONS Width: 860 mm. Depth: 500 mm. Height: 88 mm. Weight: 8 Kg. CUT OUT DIMENSIONS Width: 830 mm. Depth: 470 mm. Thickness: 30 mm. SUPPLY CONNECTIONS Gas:RC 1/2 inch (1/2 inch male) Rear right hand cornerElectric:230-240V 50Hz supply, 3 core flexible cable withnon rewireable plug fi...
Page 14 - Important safety requirements; Location
14 Important safety requirements This hob must be installed in accordance with the Gas Safety(Installation and Use) Regulations (Current Edition) and the IEE WiringRegulations (Current Edition). Detailed recommendations are contained in the following BritishStandards Codes Of Practice: B.S. 6172/ B....
Page 16 - Gas Connection
16 A) End of shaft with nutB) WasherC) Elbow FO 0814 FO 0264 this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded elbow,adjustment is fixed so that the washer is fitted between the components asshown in the diagram. Screw the parts together without using excessivefo...
Page 17 - Cut Out Size; Building In; Building over a cupboard or drawer
17 830 470 55 min. 860 500 FO 2407 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will benecessary to fit a heat resistant board below the base of the hob onthe underside ...
Page 18 - Building over a kitchen unit with door
18 ON/OFF SWITCH FLEXOUTLET ON/OFF SWITCH FLEXOUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arrangements must betaken in designing the furnitureunit, in order to avoid any contactwith the bottom of the hob whichcan be heated when it is operated.The recommended solution iss...
Page 19 - Fitting the hob to the worktop
19 Building in Fitting the hob to the worktop Before fitting the hob into thecut out, a sealing gasketsupplied with the hob must befitted to the edge of the cutout. It is essential that no gapsare left in this seal in order toprevent spillage near the hobseeping into the cabinet below. 1) Place the ...
Page 20 - Electrical connections
20 Electrical connections Any electrical work required to install this hob should be carried outby a qualified electrician or competent person, in accordance with thecurrent regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not beobserved. Th...
Page 21 - Permanent Connection; Wiring diagram; Replacement of the cable
21 Permanent Connection In the case of a permanent connection, it is necessary that you installa double pole switch between the hob and the electricity supply(mains), with a minimum gap of 3 mm. between the switch contactsand of a type suitable for the required load in compliance with thecurrent ele...
Page 22 - Fault Finding; Preliminary Electrical Systems Check
22 Fault Finding Preliminary Electrical Systems Check STARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown? Carry out:C: Polarity check. Electricity supplyshould now besatisfactory. Carry out:D: Resistance toEarth check. Inlet wiringfaulty.Rectify anyfault. Isolate appl...
Page 24 - Ignition System / Gas Ignition
24 Check gas supply atburner Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fittingof burners Check position of theelectrode Check by pass simmeradjusted...
Page 25 - Commissioning; Pressure Testing
25 Commissioning When the hob has been fully installed it will be necessary to check theminimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several t...
Page 26 - Conversion from Natural Gas to LPG; Method; TO ADJUST THE GAS RATE
26 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gasbut can be converted for use with butane or propane gas providing thecorrect injectors are fitted and the gas rate is adjusted to suit. Method 1) Ensure that the gas taps are in the 'OFF...
