Adder SV4 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Table of Contents:
Page 2 – About this manual; Warranty
Page 3 – Radio Frequency Energy
Page 4 – Contents
Page 12 – E e
Page 17 – Using the SmartView
Page 19 – ba
Page 22 – SmartView configuration options
Page 27 – oFRED
Page 30 – Problem Solving
Page 32 – Notes
Page 34 – SMART; Viie; I N S TA L L AT I O N & U S E
Loading the manual
SMART
V
Viie
ew
w
I N S
T A
L L
A
T
I
O
N
&
U
S
E
www.addertec.com
SMART View 2
SV2
SMART View 4
SV4
SMAR
T
VV
iiee
ww
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 - About this manual; Warranty
SmartView Installation and Use Page 1 About this manual SmartView - Installation and UseSixth edition (April 1999)Part No. ADD0026/6(c) 1999 Adder Technology Ltd. All rights reserved. Whilst every precaution has been taken in the preparation of thismanual, Adder Technology Ltd assumes no responsibil...
Page 3 - Radio Frequency Energy
SmartView Installation and Use Page 2 Radio Frequency Energy Shielded cables must be used with this equipment to maintain compliance with radiofrequency energy emission regulations and ensure a suitably high level of immunityto electromagnetic disturbances. European EMC directive 89/336/EEC This equ...
Page 4 - Contents
SmartView Installation and Use Page 3 Contents 1. Introduction..................................................................................... 5 1.1 Key features ........................................................................................... 51.2 Package contents.......................
Page 12 - E e
SmartView Installation and Use Page 11 In configure mode, options are entered by typing a letter followed by a numberfollowed by (enter). Use ESC to abort the entry of an option. The SmartView willremain in configure mode until you type 'E' (enter). For example: to set hotkey option 2 type the follo...
Page 17 - Using the SmartView
SmartView Installation and Use Page 16 3. Using the SmartView This section explains the general operation of the SmartView. We recommend thatyou read this section before starting to use the product. 3.1 Power on status At power on the SmartView selects PC number 1 and displays '1'. If a password has...
Page 19 - ba
SmartView Installation and Use Page 18 channels (see section 4.9) then only the active channels will be selected. Otherwisethe SmartView will cycle through all channels when using HOTKEYs + TAB. The hotkey command are summarised below (note that the numbers on the numerickeypad do not form part of a...
Page 22 - SmartView configuration options
SmartView Installation and Use Page 21 4. SmartView configuration options All the options described in this section are entered in SmartView configure mode -see section 2.5 for instructions on entering configure mode. 4.1 Screen saver time delay SmartView contains a programmable screen saver which w...
Page 27 - oFRED
SmartView Installation and Use Page 26 keyboard (except ctrl, alt, shift and enter). Consequently the following 'password'would be valid: oFRED g g 4.8 Cascade query code The SmartViews use a special ‘query code’ to detect whether or not they areconnected to another SmartView. By default your SmartV...
Page 30 - Problem Solving
SmartView Installation and Use Page 29 Appendix B. Problem Solving Problem: Poor video quality with smearing fuzziness or ripple. Action: Use screened coaxial video cables to connect your devices to the SmartView. Problem: Mouse does not move cursor on screen. Action: Ensure that the mouse and compu...
Page 32 - Notes
Page 34 - SMART; Viie; I N S TA L L AT I O N & U S E
SMART V Viie ew w I N S TA L L AT I O N & U S E ADDER Technology Limited Technology House Trafalgar Way Bar Hill Cambridge CB3 8SQ • England T: +44 (0) 1954 780044 F: +44 (0) 1954 780081 [email protected] www.addertec.com SV-05.02/V1