Page 3 - Disclaimers; Al l r i g h t s r e s e r ve d .
1 Disclaimers The information in this manual has been carefully checked and is believed to be accurate. ACNODES Co., Ltd. assumes no responsibility for any infringements of patents or other rights of third parties, which may result from its use. ACNODES assumes no responsibility for any inaccuracies...
Page 4 - Safety Approvals; FCC Co mpliance
m CE Marking m FCC Class A Safety Approvals FCC Co mpliance This equipment has been tested and complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential install...
Page 5 - Safety Precautions
1 Safety Precautions B e f o r e g e t t i n g s t a r t e d , r e a d t h e f o l l o w i n g i m p o r t a n t c a u ti o n s . 1. The PC 8150 does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. 2. Be sure to g...
Page 6 - Tra dema r ks Acknow l edgm ents
5. Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: ...
Page 7 - This page does not contain any information.
Page 8 - C h a p t e r 1; Table of Contents
Table of Contents Disclaimers.......................................................................ii Safety Approvals................................................................iii FCC Compliance ............................................................. iii Safety Precautions ................
Page 9 - DOS; A p p e n d i x A; REQUIREMENTS; viii
Driver Installation .............................................................19 3.1 System ..................................................................19 3.2 Touch Screen .......................................................20 3.2.1 Specification ............................................
Page 11 - Introduction; G e n e r a l D e s c r i p t i o n; General Description; The PC 8150 is a TFT Touch Panel PC which equipped with Intel
Introduction 1 PC 8150 User’s Manual C h a p t e r 1 Introduction This chapter contains the general information and the detail specifications of the PC 8150. Chapter 1 includes the following sections: f G e n e r a l D e s c r i p t i o n f S ys t e m S p e c i f i c a t i o n f D i me n s i o n s f...
Page 12 - M ain CPU board; S ys t e m C h i p s e t :; Syst em
2 Introduction PC 8150 User’s Manual 1.2 Specifications 1.2.1 M ain CPU board f C P U : S o c k e t M ( 4 7 8 - p i n ) f o r I n t e l ® C o r e 2 D u o / C o r e D uo / C o r e S o l o P r o c e s s or w i t h 5 3 3 / 6 6 7 M H z . f S ys t e m C h i p s e t : I n t e l ® 9 4 5 G M + I C H * 7 M ....
Page 13 - Specifi cati on; x 3 .5 ” o r 2 x 2 .5 ” P A T A / S A T A d r i v e
Introduction 3 PC 8150 User’s Manual 1.2.3 System Specifi cati on f 1 5 ” T F T L C D f D i s k d r i ve h o u s i n g : 1 x 3 .5 ” o r 2 x 2 .5 ” P A T A / S A T A d r i v e f A C p ow er su p p l y f H e a t d i s p e n s i n g d e s ig n f N e t w e i g h t : 8 . 8 K g s f D i m e n s i o n ( m a...
Page 18 - Package list; AC power cord x 1
PC 8150 User’s Manual 1.5 Package list When you receive the PC 8150 there are following items in the package. If you can not find it, please contact ACNODES distributors. 1. PC 8150 x 1 2. AC power cord x 1 3. Panel mount kit x 7 4. CD driver x1 5. Wall / VESA mount bracket kit x 1 (Optional) 6. Rac...
Page 20 - Hardware Installation; C h a p t e r 2
PC 8150 User’s Manual 8 Hardware Installation C h a p t e r 2 Hardware Installation The PC 8150 provides lots of flexible ways for user to select different configuration such as CPU, Hard Disk and more. The chapter will show you how to install the hardware. It includes: m CPU m DRAM m Hard Disk m Se...
Page 21 - CP U and DRAM Installation; Unscrew screws to remove the rear chassis.
PC 8150 User’s Manual Hardware Installation 9 2.1 CP U and DRAM Installation The standard PC 8150 system is designed for Core 2 Duo level CPUs. The CPU board provides two 240-pin DDR2 DIMM socket that supports system memory up to 3GB. When upgrading the CPU, DRAM, please refer to the following instr...
Page 23 - HDD Installation; Unscrew screws to remove the rear chassis.
PC 8150 User’s Manual Hardware Installation 11 2.2 HDD Installation The PC 8150 offers a convenient drive bay module for users to install HDD. The PC 8150 offers one 3.5” HDD drive for users to install. If you want to install one or two 2.5” HDD, the PC 8150 also provides the 3.5” to 2.5” drive hold...
Page 26 - Serial Port Interface
PC 8150 User’s Manual 14 Hardware Installation 2.3 Serial Port Interface The PC 8150 has four onboard serial ports, COM1, COM2, COM3, COM4 are RS-232 Port Connector. The connector, COM1, COM2, COM3 are DB-9 connector, and the following table shows the pin assignments of this connector. Pin Signal Na...
Page 27 - Desktop mount
PC 8150 User’s Manual Hardware Installation 15 2.6 Mountings: Panel / Wall / Rack / VESA / Desktop mount There are four application options for the PC 8150, Panel / Wall / Rack & VESA mountings. 2.6.1 Panel M ount The PC 8150 is designed for panel mount application. To mount the PC 8150, the sta...
Page 32 - Driver Installation; C h a p t e r 3; Select all files and follow the install procedure and press OK.
PC 8150 User’s Manual 20 Driver Installation C h a p t e r 3 Driver Installation 3.1 System PC 8150 could support with Windows Vista/XP. To facilitate installation system driver, you should read the instructions in this chapter carefully before you attempt installation. 1. Panel series\PC 8150\Drive...
Page 37 - Identif y the com municati on po rt and I R Q num be r; PenMount internal settings:; Do Ca lib ra tion
PC 8150 User’s Manual Driver Installation 25 Identif y the com municati on po rt and I R Q num be r 1. For the first time installation, or changing PenMount Touch Screen’s COM port, use PMDETECT (e.g. C:\PENMOUNT\PMDETECT) to check the COM port and IRQ number. PMDETECT will save the correct data to ...
Page 38 - Initializ ing the Pe n Mount d ri v er
PC 8150 User’s Manual 26 Driver Installation mapped results by choose “3” DRAWING TEST under PM.BAT Initializ ing the Pe n Mount d ri v er If you don’t have the initialization commands in AUTOEXEC.BAT, initialize PenMount C:\PENMOUNT\PMINIT) controller before you use the PenMount Touch Screen. The d...
Page 42 - Appendix; EMBEDDED BOARD; Entering Setup; TO ENTER SETUP PRESS DEL KEY
28 Appendix PC 8150 User’s Manual A p p e n d i x A EMBEDDED BOARD BIOS Setup Appendix A describes the different settings available in the Award BIOS that comes with the EMBEDDED BOARD CPU card. Also, the instructions on how to set up the BIOS configuration are contained in this chapter. A.1 Enterin...
Page 43 - Co ntrol Ke ys; Main Menu
Appendix 29 PC 8150 User’s Manual A.2 Co ntrol Ke ys Move cursor to the previous item Up arrow Move cursor to the next item Down arrow Move cursor to the item on the left hand Left arrow Move to the item in the right hand Right arrow Main Menu -- Quit and delete changes into CMOS Esc key Status Page...
Page 44 - The Main Menu; Once you enter the Award BIOS CMOS Setup Utility, the Main Menu
30 Appendix PC 8150 User’s Manual A.4 The Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu appears on the screen. In the Main Menu, there are several Setup functions and a couple of Exit options for your selection. Use arrow keys to select the Setup Page you intend to config...
Page 45 - Standard CM OS Setup Menu; The Standard CMOS Setup Menu displays basic information about; day; date; month; year; Time
’s Manual PC 8150 User Appendix 31 A.5 Standard CM OS Setup Menu The Standard CMOS Setup Menu displays basic information about your system. Use arrow keys to highlight each item, and use <PgUp> or <PgDn> key to select the value you want in each item. a Date The date format is <day>...
Page 47 - Halt On
Appendix 33 PC 8150 User’s Manual Halt On No errors The system booting will halt on any errors detected. (default) All errors Whenever BIOS detects a non-fatal error, the system will stop and you will be prompted. All, But Keyboard The system booting will not stop for a keyboard error; it will stop ...
Page 48 - Advanced BIOS Features; up some system features according to your preference.
34 Appendix PC 8150 User’s Manual A.6 Advanced BIOS Features This section allows you to configure and improve your system, to set up some system features according to your preference. a CPU Feature Scroll to this item and press <Enter> to view the CPU Feature sub menu.
Page 49 - Enabled; Disabled
Appendix 35 PC 8150 User’s Manual a Hard Disk Boot Priority Scroll to this item and press <Enter> to view the sub menu to decide the disk boot priority. a CPU L1 & L2 Cache These two options speed up memory access. However, it depends on the CPU/chipset design. The default setting is “Enab...
Page 50 - Boot Up NumLock Status; Normal
PC 8150 User’s Manual 36 Appendix a First/Second/Third Boot Device These items let you select the 1st, 2nd, and 3rd devices that the system will search for during its boot-up sequence. The wide range of selection includes Floppy, LS120, ZIP100, HDD0~3, SCSI, and CDROM. a Swap Floppy Drive This allow...
Page 51 - Fast; Typematic Rate Setting; This option refers to character numbers typed per second by
37 PC 8150 User’s Manual Appendix Fast Default: Fast. The A20 signal is controlled by Port 92 or chipset specific method. a Typematic Rate Setting This item determines the typematic rate of the keyboard. The default value is “Disabled”. a Typematic Rate Setting Enabled Enable typematic rate and type...
Page 52 - System; NOTE
38 Appendix PC 8150 User’s Manual System If a wrong password is entered at the prompt, the system will not boot, the access to Setup will be denied, either. If a wrong password is entered at the prompt, the system will boot, but the access to Setup will be denied. Setup NOTE : To disable the securit...
Page 53 - Advanced Chipset Features; Use this item to increase the timing of the memory. This is
Appendix 39 PC 8150 User’s Manual A.7 Advanced Chipset Features This section contains completely optimized chipset’s features on the board that you are strongly recommended to leave all items on this page at their default values unless you are very familiar with the technical specifications of your ...
Page 55 - Integrated Peripherals; This section allows you to configure your SuperIO Device, IDE; IDE HDD Block Mode
41 PC 8150 User’s Manual Appendix A.8 Integrated Peripherals This section allows you to configure your SuperIO Device, IDE Function and Onboard Device. a OnChip IDE Device Scroll to this item and press <Enter> to view the sub menu OnChip IDE Device. ¤ IDE HDD Block Mode
Page 56 - IDE DMA transfer access; “Enabled”; IDE Master/Slave UDMA; Onboard Device; Scroll to this item and press to view the sub menu
42 Appendix PC 8150 User’s Manual Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can su...
Page 57 - USB Controller; Super IO Device
Appendix 43 PC 8150 User’s Manual ¤ USB Controller Enable this item if you are using the USB in the system. You should disable this item if a higher-level controller is added. ¤ USB 2.0 Controller Enable this item if you are using the EHCI (USB2.0) controller in the system. ¤ USB Keyboard Support En...
Page 58 - Onboard FDC Controller
44 Appendix PC 8150 User’s Manual ¤ Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install and-in FDC or the system has no floppy drive, select Disabled in this field. The options available are Enab...
Page 59 - Power Ma na ge m e nt Setup; The Power Management Setup allows you to save energy of your
Appendix 45 PC 8150 User’s Manual A.9 Power Ma na ge m e nt Setup The Power Management Setup allows you to save energy of your system effectively. It will shut down the hard disk and turn OFF video display after a period of inactivity. a ACPI Function This item allows you to enable/disable the Advan...
Page 60 - DPMS; Blank Screen; Suspend Mode; HDD Power Down
46 Appendix PC 8150 User’s Manual hardware maintains all system context. [S3(STR)] The S3 sleep mode is a lower power state where the information of system configuration and open applications/files is saved to main memory that remains powered while most other hardware components turn off to save ene...
Page 62 - Configu ration Setup; Init Display First
48 Appendix PC 8150 User’s Manual A.10 PnP/PCI Configu ration Setup This section describes the configuration of PCI (Personal Computer Interconnect) bus system, which allows I/O devices to operate at speeds close to the CPU speed while communicating with other important components. This section cove...
Page 63 - The default value is; PC Health Status; Current CPU Temperature
Appendix 49 PC 8150 User’s Manual interrupt to one of the following types in accordance with the type of devices using the interrupt: 1. Legacy ISA Devices compliant with the original PC AT bus specification, requiring a specific interrupt (such as IRQ4 for serial port 1). 2. PCI/ISA PnP Devices com...
Page 64 - Freque ncy/Volta ge Control; Auto Detect PCI Clk; Load Optimized Defaults
50 Appendix PC 8150 User’s Manual These read-only fields reflect the functions of the hardware thermal sensor that monitors the chip blocks and system temperatures to ensure the system is stable. A.12 Freque ncy/Volta ge Control This section is to control the CPU frequency and Supply Voltage, DIMM O...
Page 65 - Set Supervisor/User Password
Appendix 51 PC 8150 User’s Manual To load CMOS SRAM with SETUP default values, please enter “Y”. If not, please enter “N”. A.14 Set Supervisor/User Password You can set a supervisor or user password, or both of them. The differences between them are:
Page 66 - Supervisor password:; ENTER PASSWORD
52 Appendix PC 8150 User’s Manual 1. Supervisor password: You can enter and change the options on the setup menu. 2. User password: You can just enter, but have no right to change the options on the setup menu. When you select this function, the following message will appear at the center of the scr...
Page 67 - PASSWORD DISABLED; When a password is enabled, you have to type it every time you enter
Appendix 53 PC 8150 User’s Manual To disable the password, just press <Enter> when you are prompted to enter a password. A message will confirm the password is getting disabled. Once the password is disabled, the system will boot and you can enter Setup freely. PASSWORD DISABLED When a passwor...
Page 68 - Exit Without Saving
54 Appendix PC 8150 User’s Manual A.16 Exit Without Saving Select this option to exit the Setup utility without saving changes you have made in this session. Type “Y”, and it will quit the Setup utility without saving your modifications. Type “N” to return to the Setup utility.
Page 69 - Appendix B; REQ UIREMENTS; O U T P U T E L E CT RI CAL R E Q UI R E ME NT S
Appendix 55 PC 8150 User’s Manual Appendix B Power Supply Specification B.1 Power Supply: FSP180-50PLA1 (180W, AC 110~230V Input) B.1.1 ELECTRI CAL REQ UIREMENTS O U T P U T E L E CT RI CAL R E Q UI R E ME NT S The subject power supply will meet all electrical specifications below, over the full ope...
Page 70 - L O A D CA PAC IT Y S P EC I F I C AT I O NS; OUTPUT RISE TIME
56 Appendix PC 8150 User’s Manual L O A D CA PAC IT Y S P EC I F I C AT I O NS The cross regulation defined as follows, the voltage regulation limits DC include DC Output ripple & noise. +3.3V +5V +12V -12V L O A D S T M ALL MAX HHHH 4.5A 9.0A 9.0A 0.8A LHLL +5V MAX 0.3A 12.0 A 1.5A 0.0A other M...
Page 71 - SH ORT C I RC UIT PR OT E CTI ON
Appendix 57 PC 8150 User’s Manual SH ORT C I RC UIT PR OT E CTI ON Output short circuit is defined to be a short circuit load of less than 0.1 ohm. In the event of an output short circuit condition on +3.3V, +5V or +12V output, the power supply will shutdown and latch off. The power supply shall ret...
Page 72 - REQUI REM ENTS; O p e r a t i n g t e m p e r a t u r e r a n g e :; and nominal AC input voltage.
58 Appendix PC 8150 User’s Manual TTL signal asserted (high state): greater than 4.75V while sourcing 500uA. High state output impedance: less or equal to 1Kohm from output to common. 100 –500mSec. P O W E R G O O D @ 1 1 5 / 2 3 0 V , F U L L L O A D 1 mSec. minimum P O W E R F A I L @ 1 1 5 / 2 3 ...
