Page 2 - Disclaimers; All right s reser ved.
Disclaimers The information in this manual has been carefully checked and is believed to be accurate. Acnodes Co., Ltd. assumes no responsibility for any infringements of patents or other rights of third parties, which may result from its use. Acnodes assumes no responsibility for any inaccuracies t...
Page 3 - Safety Approvals; FCC Compliance; that to which the receiver is connected.
‹ CE Marking ‹ FCC Class A Safety Approvals FCC Compliance Thi s equipment has been tested and complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential install...
Page 4 - Safety Precautions
Safety Precautions Before getting started, read the following important cautions. 1. The PC 6170 does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. 2. Be sure to ground yourself to prevent static charge when ins...
Page 5 - Do not open the system’s back cover. If opening the cover for; Trademarks Acknow ledgments
5. Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: ...
Page 7 - Table of Contents
Table of Contents Chapter 1 Introduction ------------------------------- 1 1.1 General Description ........................................... 1 1.2 Specifications .................................................... 2 1.3 Dimensions ........................................................ 5 1.4 Fro...
Page 9 - General Description; Front Access USB Ports & OSD; The Pentium®-M processor delivers outstanding
PC 6170 User’s Manual C h a p t e r 1 Introduction This chapter contains the general information and the detail specifications of the PC 6170. Chapter 1 includes the following sections: „ General Description „ System Specification „ Dimensions „ Front View & I/O Outlets „ Package List 1.1 Genera...
Page 10 - Main CPU board; Introduction
PC 6170 User’s Manual a high stability and high reliable Panel PC. At the same time, with the Ultra Slim case design, customers can easily install PANEL1170-810 everywhere. Easy-to-Maintenance Design: Back Door The back panel of the PC 6170 was anchored by hand-removable fasten screws. Users can ins...
Page 11 - Ethernet; channels up to 6 devices (2 parallel ATA-100 and 2
PC 6170 User’s Manual I/O System „ Standard I/O: − 3 x serial ports with power; 2 x RS-232, 1 x RS-232/422/485 jumper selectable − 1 x parallel port, SPP/EPP/ECP − 1 x PS/2 for Keyboard Interface − 1 x PS/2 for Mouse Interface − 3 x USB Ports 2.0 compliant(1 at rear; 2 at front panel) − 1 x 1 5 pin(...
Page 12 - System Specification; 80W AC power supply
PC 6170 User’s Manual System Specification „ 17” TFT LCD „ Disk drive housing: − 1x Build-in Slim type FDD, − 1x optional slim type CD-ROM diver, − 1 x internal 3.5” drive (or 2X 2.5” HDD) 180W AC power supply Heat dispensing design One slot for PCI expansi on Net weight: − 13.5 Kgs Dimension (main ...
Page 16 - list; Panel mount kit x 10
PC 6170 User’s Manual 1.5 Package list When you receive the PC 6170 there are following items in the package. 1. P1170-810 x 1 2. CPU cooler x 1 3. AC power cord x 1 (U.S standard) 4. Panel mount kit x 10 5. Desktop kit x 2 6. VESA ARM kit x 1 7. Wall mount kit x 1 8. CD driver x1 8 Introduction
Page 17 - CPU and DRAM Installation; Unscrew five screws in the back door.
PC 6170 User’s Manual C h a p t e r 2 Hardware Installation The PC 6170 provides lots of flexible ways for you to select different configuration such as CPU, CD-ROM and more. The chapter will show you how to install the hardware. It includes: 2.1 CPU and DRAM Installation The standard PC 6170 system...
Page 18 - Hardware Installation
PC 6170 User’s Manual 2. Install the CPU, DDR DRAM and Mini-PCI card in the P-1170-810. DRAM CPU Mini-PCI 10 Hardware Installation
Page 19 - HDD Installation
PC 6170 User’s Manual 2.2 HDD Installation The PC 6170 offers a convenient drive bay module for users to install HDD. The PC 6170 offers one 3.5” HDD drive for users to install. If you want to install two 2.5” HDDs, the PC 6170 also provides the 3.5” to 2.5” drive holder to meet your requirement. Pl...
Page 24 - x Serial Ports
PC 6170 User’s Manual 2.5 3 x Serial Ports The PC 6170 provides three onboard serial ports installed on the back bottom side of the chassis. For systems, COM1 and COM2 are RS-232 and COM4 is RS-232/422/485. Each serial port is with +5V/+12V power capabilities on both Pin 1 and Pin 8, ready to accomm...
Page 33 - Select all files and follow the install procedure and press OK.
PC 6170 User’s Manual C h a p t e r 3 Driver Installation 3.1 System PC 6170 could support with Windows 95, Windows 98 or Windows 2000/XP. To facilitate installation system driver, you should read the instructions in this chapter carefully before you attempt installation. 1. Insert Driver CD and sel...
Page 34 - Driver Installation
PC 6170 User’s Manual 3.2 Touch Screen 3.2.1 Specification To u c h S c r e e n : For 8-wire analog resistive type T o u c h S c r e en C o nt r o l l er : DMC9000 Co mm u n i c a t io ns : RS-232 Ba ud R a te : 19200 baud rate fixed Re s o lu tion: 1024 x 1024 (10-bit A/D converter inside) Po w e r...
Page 37 - PenMount internal settings:
PC 6170 User’s Manual 3.2.3 Driver Installation- DOS Using “INSTALL.EXE” utility to install PenMount software driver. 1. Insert Driver CD and select the \P1170-810\Driver\Touch screen\DOS\ Install.exe 2. Press ENTER key to install the drivers to drive C or use keyboard to key-in the hard disc drive ...
Page 39 - Install PenMount driver; Follow the install procedure and press OK.; Advance Setup; Before install the Touch Screen Driver, please open the file in
PC 6170 User’s Manual 3.2.4 Driver Installation- Linux Install PenMount driver 1. Insert Driver CD and select the “\P1170-810\Driver\Touch\Linux XFree86 4.x.x Driver V2.1\Driver\penmount_drv.o” 2. Follow the install procedure and press OK. 3. Please reboot system. 4. Click Start menu and select “Pen...
Page 40 - Do Calibration
PC 6170 User’s Manual 2. Key-in the following words. Setserial /dev/ttyS2 port 0x3e8 irq 10 (set COM3 as touch screen port) 3. Save and exit. 4. Please reboot. 5. After reset system, Insert Driver CD. Do Calibration 1. Insert Driver CD and select the “\P1170-810\Driver\Touch\Linux XFree86 4.x.x Driv...
Page 43 - C h a p t e r 4; Windows XP Embedded; Penmount Touch Screen
PC 6170 User’s Manual C h a p t e r 4 Embedded O.S. Installation 4.1 Windows XP Embedded Supported devices are as follows: Onboard Multi I/O „ Floppy drive „ Parallel port „ 16C550 UARTs compatible serial port „ IrDA for wireless communication Onboard IDE „ IDE HDD „ IDE CDROM USB PS2 Keyboard and m...
Page 45 - A p p e n d i x A; A.1 Standard CMOS Setup Menu; CMOS Setup Utility-Copyright © 2000-2004 Aw ard S o f tw are
PC 6170 User’s Manual A p p e n d i x A SBC83810 BIOS Setup The board used in the PC 6170 is SBC83810. The different settings available in the Award BIOS that comes with the SBC83810 . Also contained here are instructions on how to set up the BIOS configuration. A.1 Standard CMOS Setup Menu The item...
Page 46 - Date; Ti me
PC 6170 User’s Manual Date The date format is <day>, <date> <month> <year>. Press <F3> to show the calendar. day T h e d a y o f we e k , f r o m Su n to S a t, d e te rm i n e d b y th e B IO S , i s r ea d o n l y date T h e d a te , fr o m 1 to 3 1 (o r th e ma x imu...
Page 47 - Drive A type/Drive B type; None; Halt On; No errors
PC 6170 User’s Manual Drive A type/Drive B type The category identifies the types of floppy disk drive A or drive B installed in the computer. None No floppy drive installed 360K, 5.25 in 5.25 inch P C-type standard drive; 360K b capacity 1.2M, 5.25 in 5.25 inch A T-type high-density dri ve; 1.2M B ...
Page 48 - A.2 Advanced BIOS Features
PC 6170 User’s Manual A.2 Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference. CMOS Setup Utility-Copyright © 2000-2004 Aw ard S o f tw are Ad vanced BIOS Featur es C P U F e a tur e P re ss E ...
Page 49 - Hard Disk Boot Priority; Virus Warning; Quick Po wer On Self Test
PC 6170 User’s Manual Hard Disk Boot Priority This item can select boot device priority. Virus Warning This option flashes on the screen. During and after the system boot up, any attempt to write to the boot sector or partition table of the hard disk drive will halt the system with the following mes...
Page 50 - Boot O th er Dev ice; Swap Floppy Drive; Boot Up Nu mLock Status; Gate A20 Op tion
PC 6170 User’s Manual First/Second/Third Boot D evice These items allow the selection of the 1 st , 2 nd , and 3 rd devices that the system will search for during its boot-up sequence. The wide range of selection includes Floppy, LS120, ZIP100, HDD0~3, SCSI, and CDROM. Boot O th er Dev ice This item...
Page 51 - Typematic Rate Setting
PC 6170 User’s Manual Typematic Rate Setting This determines the typematic rate of the keyboard. The default value is “ Disabled ” . Enabled Enable typematic rate and typemati c delay programming Disable typem atic rate and typem atic delay Disabled programming. The system BIOS will use default valu...
Page 52 - Security Option; System; OS Select f or D RA M >64MB
PC 6170 User’s Manual Security Option This item allows you to limit access to the system and Setup, or just to Setup. The default value is “ Setup ” . System The system will not boot and access to Setup w ill be denied if the incorrect password is entered at the prompt. Setup The system w ill boot, ...
Page 53 - A.3 Advanced Chipset Features; CMOS Setup Utility-Copyright © 1984-2001 Aw ard S o f t w are; SDRAM CAS latency Time
PC 6170 User’s Manual A.3 Advanced Chipset Features Since the features in this section are related to the chipset on the CPU board and are completely optimized, you are not recommended to change the default settings in this setup table unless you are well oriented with the chipset features. CMOS Set...
Page 55 - A.4 Integrated Peripherals; This option sets your hard disk configuration, mode and port.
PC 6170 User’s Manual A.4 Integrated Peripherals This option sets your hard disk configuration, mode and port. CMOS Setup Utility-Copyright © 1984-2001 Aw ard S o f t w are Integrated Peripherals ► O n Ch i p I DE D e v i ce P re s s En t er ► O n Bo a r d De v i ce P re s s En t er Me n u L e ve l ...
Page 58 - Onboard FDC Controller; Parallel Port Mode
PC 6170 User’s Manual BUTTON-ONLY Follows the conventional way of turning OFF system power (via power button). Upon selecting this option, the K B POWER ON Password line appears. Press <E nter> and you’ll be Password Hot KEY prompted to enter and confi rm a password of your choi ce. After sett...
Page 59 - ECP Mode Use DMA
PC 6170 User’s Manual ECP Mode Use DMA Select a DMA channel for the parallel port for use during ECP mode. SBC83810 BIOS Setup 51
Page 60 - A.5 Power Management Setup
PC 6170 User’s Manual A.5 Power Management Setup The Power Management Setup allows you to save energy of your system effectively. It will shut down the hard disk and turn OFF video display after a period of inactivity. CMOS Setup Utility-Copyright © 1984-2001 Aw ard S o f t w are Pow er Manag ement ...
Page 61 - Video Off Method
PC 6170 User’s Manual ACPI Fu nction This item allows you to enable/disable the Advanced Configuration and Power Management (ACPI). The options available are Enabled, Disabled. Po wer M anagement This option allows you to select the type (or degree) of power saving for Doze, Standby, and Suspend mod...
Page 62 - Video Off After; Mo de m U se IRQ; Standby M od e; Suspend Mode
PC 6170 User’s Manual Video Off After As the system moves from lesser to greater power-saving modes, select the mode in which you want the monitor to blank off. The default value is “ Standby ” . NA System BIOS will never turn off the screen Suspend Screen off when system is in SUS PEND mode Standby...
Page 63 - HDD Po wer Down; Throttle Duty Cy cle; Po wer On by Ring; IRQ 8 Break Suspend
PC 6170 User’s Manual 1/2/4/6/8/10/20/ 30/40 Min/1 Hr HDD Po wer Down Defines the continuous idle time before the system entering SUSPEND mode. If any item defi ned in (J) i s enabled & active, S USPEND timer will be reloaded After the selected period of drive inactivity (1 to 15 minutes), the h...
Page 64 - Reload Global Timer Events
PC 6170 User’s Manual does not awaken the system from Suspend mode. The default value is “ Disabled ” . Reload Global Timer Events When Enabled , an event occurring on each device listed below restarts the global time for Standby mode. 56 SBC83810 BIOS Setup
Page 65 - PNP OS Installed
PC 6170 User’s Manual A.6 PnP/PCI Configuration Setup This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. Thi...
Page 67 - A.7 PC Health Status; Current CPU Temperature
PC 6170 User’s Manual A.7 PC Health Status This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value. CMOS Setup Utility-Copyright © 1984-2001 Aw ard S o f t w are PC Healt h Status CP U Wa rn ing T em p e ra tur e D...
Page 68 - Auto Detect DI MM/PCI Clk; Speed Spectrum
PC 6170 User’s Manual A.8 Frequency/Voltage Control This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value. CMOS Setup Utility-Copyright © 1984-2001 Aw ard S o f t w are Frequency/Voltag e Control A u to D e t e c...
Page 69 - CMOS Setup Ut ility-Copyright © Aw ard Softw are; To load BIOS defaults value to CMOS SRAM, enter
PC 6170 User’s Manual A.9 Load Fail-Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features. CMOS Setup Ut ility-Copyright © Aw ard Softw are ` Standard CMOS F...
Page 70 - A.10 Load Optimized Defaults
PC 6170 User’s Manual A.10 Load Optimized Defaults This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features. CMOS Setup Ut ility-Copyright © Aw ard Softw are ` Standard CMOS Features ` Frequency/Voltag...
Page 71 - ELECTRICAL REQUIREMENTS; OUTPUT ELECTRICAL REQUIREMENTS; Power Supply Specification
PC 6170 User’s Manual Appendix B Power Supply Specification Power Supply: FSP180-50PLA1 ( 180W, AC 110~230V Input) ELECTRICAL REQUIREMENTS OUTPUT ELECTRICAL REQUIREMENTS The subject power supply will meet all electrical specifications below, over the full operation temperature range and dynamic load...
Page 72 - L O A D CAP AC ITY S PE CIFIC A TI O NS; OUTPUT RISE TIM E
PC 6170 User’s Manual L O A D CAP AC ITY S PE CIFIC A TI O NS The cross regulation defined as follows, the voltage regulation limits DC include DC Output ripple & noise. LOAD S T M +3.3V +5V +12V -12V ALL MAX HHHH 4.5A 9.0A 9.0A 0.8A +5V MAX other MIN +3.3V MAX other MIN +12V MAX other MIN LHLL ...
Page 73 - S H ORT CIR CUIT PR OT ECTIO N; the power switch has been turned off for no more than 2 seconds.; O VE RLO A D PROTE C T I O N; conditions starting at full load before it is latched off.; POWER GOOD SIGNAL; procedure under normal input operating conditions.
PC 6170 User’s Manual S H ORT CIR CUIT PR OT ECTIO N Output short circuit is defined to be a short circuit load of less than 0.1 ohm. In the event of an output short circuit condition on +3.3V, +5V or +12V output, the power supply will shutdown and latch off. The power supply shall return to normal ...
Page 74 - non-recoverable failure or deviation from
PC 6170 User’s Manual TTL signal asserted (high state): greater than 4.75V while sourcing 500uA. High state output impedance: less or equal to 1Kohm from output to common. P O W E R G OOD @ 11 5 / 2 3 0V ,FULL LOA D 100 –500mSec. P O WER FAIL @ 1 15 / 2 3 0 V , FULL LOAD 1 mSec. minimum EFFICIENCY 1...
Page 75 - Plane of vibration to be along three mutually perpendicular axes.; SHOCK; Storage
PC 6170 User’s Manual non-resonant excursions. Plane of vibration to be along three mutually perpendicular axes. SHOCK The subject power supplies will withstand the following imposed conditions without experiencing non-recoverable failure or deviation from specified output characteristics. Storage –...
