Page 2 - D isc la ime rs; ©Copyright 2003 by Acnodes Corp. All rights; ii
D isc la ime rs The information in this manual has been carefully checked and is believed to be accurate. Acnodes Corp. assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Acnodes Corp assumes no responsibility for any inaccuraci...
Page 3 - E S D P r e c a u t i o n s; T r a d e m a r k s A c k n ow l e d g m e n t s; Machines Corporation.
E S D P r e c a u t i o n s Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: • Do not remove boards or integrated circuits from their anti-static packaging until you are ready to insta...
Page 4 - U n p a c k in g; After unpa; cludes the following:; What To Do If There Is A Problem; iv
U n p a c k in g The FPC-8057 is packed in an anti-static bag. The product has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety instructions in front of this User’s Manual describe anti-static precaution...
Page 5 - Safe ty Instructions; O v e r v i e w; Dangerous Voltage Warnings:
Safe ty Instructions O v e r v i e w This section states the safety instructions, which must be followed when installing, operating and servicing the FPC-8057. If neglected, physical injury and death may follow, or damage may occur to controller and related equipment. The material in this chapter mu...
Page 6 - Electrostatic Discharge Warning:; vi
damage equipment. General warning: Warns of situations, which can cause physical injury and or damage equipment by means other than electrical. Electrostatic Discharge Warning: Warns of situations in which an electrostatic discharge can damage equipment. Readers are notified of the need for special ...
Page 7 - vii
Table of Contents Disclaimers --------------------------------------------------------ii ESD Precautions --------------------------------------------------iii Unpacking ---------------------------------------------------------i v Safety Instructions ------------------------------------------------ v...
Page 8 - Appendix C How to use development tools-eMbedded
2.4 CE Requirements .......................................................... 18 2.5 Dimensions of FPC-8057 ............................................. 19 Chapter 3 Windows CE.NET ------------------------------ 21 3.1 Introduction ............................................................... 21...
Page 9 - Gen eral Descrip tion; The FPC-8057 series are fan-less and compact-size touch panel
FPC-8057 User’s Manual C h a p t e r 1 I n t r o d u c t i o n 1.1 Gen eral Descrip tion The FPC-8057 series are fan-less and compact-size touch panel computers. It equips with 5.7” STN LCD display, Windows CE.NET and low power consumption CPU, Intel Xscale PXA255. Therefore, FPC- 8057 series are go...
Page 13 - M o u n t i n g I n s t r u c t i o n s; Panel Details; Installation Instructions
FPC-8057 User’s Manual Chapter 2 Insta llation Instru ctio ns 2.1 M o u n t i n g I n s t r u c t i o n s 2.1.1 Location Considerations Care should be taken when locating equipment behind the unit to ensure that AC power wiring, PLC output modules, contactors, starters and relays, and any other sour...
Page 16 - . 2 P o w e r C o n n e c t i o n s
FPC-8057 User’s Manual 2 . 2 P o w e r C o n n e c t i o n s Make sure that all local and national electrical standards are met when the installing the unit. Contact your local authorities to determine which codes apply. Installation Instructions 8
Page 18 - Connection
FPC-8057 User’s Manual common paired with a hot or signal line. If wiring is to be exposed to lightning or surges, use appropriate surge suppression devices. Keep AC, high energy, and rapidly switching DC wiring separate from signal wires. Equip ungrounded DC supplies with a resistor and capacitor i...
Page 19 - Requirements
FPC-8057 User’s Manual FUSE Replacement: The fuse use on FPC-8057 is: BUSSMANN Fast Acting, Glass Tube Rating: 250VAC, 1A Size: 5x20mm Warning: Make sure the power off before replace the fuse. Do not replace the fuse with a different rating fuse. 1. 2. 2.2.2 Grounding Requirements Chassis ground mus...
Page 20 - Hardware Considerations WARNING!
FPC-8057 User’s Manual 2.2.3 CE Requirements To make a FPC-8057 comply with EMC directives, and to reduce susceptibility to electrical interference, a separate #14 AWG ground wire should be taken to the chassis ground terminal of the power connector. This ground connection should be run directly to ...
Page 22 - . 3 C o m m u n i c a t i o n s C o n n e c t i o n s; Cable
FPC-8057 User’s Manual 2 . 3 C o m m u n i c a t i o n s C o n n e c t i o n s There are several ports in the back of the case. Please take the following information for reference. 2.3.1 COM 1 [RS-232] Different cables are required for various devices. Cable Requirements Caution Restrict cable lengt...
Page 23 - Pin Designations
FPC-8057 User’s Manual Pin assignment of the 9 Pin, Female, SUB-D, COM1 [RS-232] Port. Pin Designations Note: This port is not used for downloading or for printing functions. COM1 [RS-232] Pin# Symbol Function 1 DCD Data Carrier Detect 2 RxD Received Data 3 TxD Transmitted Data 4 DTR Data Terminal R...
Page 24 - GND GND; used
FPC-8057 User’s Manual 2.3.2 COM2 [RS-232] & COM3 [RS-422/485] The 9 Pin, male, SUB-D, COM2 [RS-232] & COM3 [RS-422/485] Port on the back of the unit is the downloading port (PC Connector) and RS-485/422 communications port for connecting to a device. Connector COM2 [RS-232] & COM3 [RS-2...
Page 26 - . 4 C E R e q u i r e m e n t s; EU directives that apply to the FPC-8057 Series:
FPC-8057 User’s Manual z Boot Loader mode: Load new Windows CE.NET image file. If the FPC- 8057 already load the CE image with boot loader. Set the DIP SW2 ON then power ON into boot loader mode. Refer the load Win CE image document. 2 . 4 C E R e q u i r e m e n t s EU directives that apply to the ...
Page 27 - . 5 D i m e n s i o n s o f F P C - 8 0 5 7
FPC-8057 User’s Manual 2 . 5 D i m e n s i o n s o f F P C - 8 0 5 7 19 Installation Instructions
Page 29 - I n t r o d u c t i o n; Windows CE.NET platform. Designed from the ground up for the
FPC-8057 User’s Manual C h a p t e r 3 W i n d o w s C E . N E T 3.1 I n t r o d u c t i o n The FPC-8057 series operator interface terminal is designed to serve on the Windows CE.NET platform. Designed from the ground up for the embedded marketplace, Windows CE.NET delivers a robust real-time opera...
Page 34 - MAC address; The MAC address p; S ave; folder. Next time reboot
FPC-8057 User’s Manual MAC address The MAC address p age the block shows the network MAC address. S ave T ap the Save registry button, would save the reg istry data to the IPSM folder. Next time reboot the FPC-8057, Window s CE.NET system will use the stored registry data. 26 Windows CE.NET
Page 38 - To create a new Remote Desktop Connection; XP Professional that has Remote Desktop enabled and for which you
FPC-8057 User’s Manual To create a new Remote Desktop Connection 1. Open Remote Desktop Connection. 2. In Computer, type the computer nam e for your computer running Windows XP Professional that has Remote Desktop enabled and for which you have Remote Desktop permissions. 29 Windows CE.NET
Page 40 - . 3 F P C - 8 0 5 7 N e t w o r k i n g
FPC-8057 User’s Manual 3 . 3 F P C - 8 0 5 7 N e t w o r k i n g 3.3.1 Networking via Ethernet The FPC-8057 is equipped with a 10Base-T Ethernet controller. To utilize it, change the device name when the FPC-8057 is first turned on. Step 1 Click “Start/Settings/Control ___ Panel” ___________________...
Page 41 - cecp
server, please consult with MIS to get specific IP address. Click “Start/Settings/Control Panel”. Double click “Network and Dial-up Connections” and update ___ the IP address. _______________________________________ 6 Use the cecp utility “Save registry” to save this changed. The FPC-8057 can use th...
Page 43 - can be used to browse web pages on World Wide Web via LAN or dial-up
FPC-8057 User’s Manual 3.3.3 Web browser The FPC-8057 built-in Windows CE.NET OS includes Microsoft IE sample. It can be used to browse web pages on World Wide Web via LAN or dial-up connection. 34 Windows CE.NET
Page 44 - . 4 A p p l i c a t i o n p ro g r a m d e v e l o p m e n t
FPC-8057 User’s Manual 3 . 4 A p p l i c a t i o n p ro g r a m d e v e l o p m e n t The FPC-8057 is bundled with built-in Windows CE.NET operating system and with Compact Framewrok. In real applications users need to execute various applications programs on it. However, unlike its other family the...
Page 47 - When installation is; “Completing; The installer; “Finish”
FPC-8057 User’s Manual When installation is 3 complete the following message should appear: “Completing the FPC-8057 Setup Wizard”. The installer must press the “Finish” button in the install window to exit. 38 Windows CE.NET
Page 48 - The FPC-8057 offers loop back test program for two comports. Please; S e r i a l p o r t l o o p b a c k t e s t p r o g r a m; Before running the program, you need to connect two comports of the
FPC-8057 User’s Manual Appendix A Examp le P rog ram The FPC-8057 offers loop back test program for two comports. Please select the program D:\FPC-8057\Example\Serial Test. S e r i a l p o r t l o o p b a c k t e s t p r o g r a m Before running the program, you need to connect two comports of the F...
Page 50 - If you want to update new WindowsCE image to FPC-8057, you can follow
FPC-8057 User’s Manual A p p e n d i x B H o w t o U p d a t e W i n d o w s C E i m a g e If you want to update new WindowsCE image to FPC-8057, you can follow the procedure. 1. Download newest version of WindowsCE image from Acnodes’ website. www.acnodes.com 2. Save new WindowsCE image into Compac...
Page 51 - How to Update WindowsCE image
FPC-8057 User’s Manual This page does not contain any information. 42 How to Update WindowsCE image
Page 52 - The following procedure will show you how to use development
FPC-8057 User’s Manual Appendix C How to use development tools- eMbedded C++4.0 The following procedure will show you how to use development tools-eMbedded C++4.0. 1. Before you start to develop the application program, you need to install following three S/W to Host PC. (1) USB driver in the driver...
Page 53 - How to use development tools
FPC-8057 User’s Manual 2. Plug synchronized cable which is in the package to the USB client port of the FPC-8057. 3. Run Microsoft ActiveSync. software. 44 How to use development tools
