Page 2 - Preface
Confidential i X1161/X1261/X1161A/X1161N/X110/H5360 Preface This manual is applied to X1161/X1261/X1161A/X1161N/X110/H5360 projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product.Your customers will appreciate the quick r...
Page 4 - Table of Content; Chapter 1 Introduction
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential iii Table of Content Chapter 1 Introduction Highlight 1-1 Compatible Mode 1-5 Product Overview 1-9 Chapter 2 Disassembly Process & Assembly Process Equipment Needed & Product Overview 2-1 Disassemble Lamp Cover Module 2-2 Disassemble Lamp Mod...
Page 5 - Chapter 3 Troubleshooting
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential iv Assemble Bottom Shielding 2-17 Assemble Interrupt Switch 2-17 Assemble Lamp Driver Module 2-18 Assemble LVPS Module 2-19 Assemble Blower 2-19 Assemble System Fan Module 2-20 Assemble Focus Ring 2-21 Assemble Zoom Ring 2-21 Assemble DMD Chip and DM...
Page 6 - Chapter 5 Firmware Upgrade; Appendix C
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential v Calibration 4-7 Video Performance 4-9 Optical Performance Measure 4-10 Others 4-12 Chapter 5 Firmware Upgrade Equipment Needed 5-1 DLP Composer Lite Setup Procedure 5-2 USB Driver Upgrade Procedure (for X1161 only) 5-4 Firmware Upgrade Procedure 5-...
Page 7 - Chapter 1; Introduction
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 1-1 Chapter 1 Introduction 1-1 Highlight No Item Description 1 Dimensions (W x H x D) ● 268 mm x 192 mm x 80 mm 2 Weight ● <4.9 lbs 3 Tilt Angle ● 2.7 degree with elevator mechanism 4 Power Supply ● Universal AC 100 – 240 V ~ 50-60 Hz with PFC inp...
Page 14 - Compatibility
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 1-8 Compatibility Resolution V.Frequency [Hz] H.Frequency [KHz] (2) VGA Analog - Extended Wide timing WXGA 1280 x 768 60 47.8 1280 x 768 75 60.3 1280 x 768 85 68.6 1280 x 720 60 44.8 1280 x 800 60 49.6 1366 x 768 60 47.71 WXGA+ 1440 x 900 60 55.9 WSX...
Page 15 - Projector Outlook
Confidential 1-9 X1161/X1261/X1161A/X1161N/X110/H5360 1-3 Product Overview Projector Outlook Front /Upper side Item Description Item Description 1 Ventilation (inlet) 6 Lens cap 2 Ventilation (outlet) 7 Power button 3 Remote control receivers 8 Remote control 4 Focus ring 9 Zoom lever 5 Zoom lens 10...
Page 18 - Remote Control and Control Panel Layout
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 1-12 Remote Control and Control Panel Layout
Page 20 - Getting Started
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 1-14 Getting Started Connecting the Projector Item Description Item Description 1 Power cord 6 S-Video cable 2 VGA cable 7 Audio cable jack/jack 3 Composite video cable 8 Audio cable jack/RCA 4 RS232 cable 9 USB cable Note: To ensure the projector wo...
Page 24 - Bottom Cover Dimension
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 1-18 Bottom Cover Dimension
Page 25 - Chapter 2; Disassembly & Assembly Process
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-1 Chapter 2 Disassembly & Assembly Process 2-1 Equipment Needed & Product Overview 1. Screw Bit (+): 1052. Screw Bit (+): 1073. Screw Bit (-): 1074. Hex Sleeves 5mm5. Long Nose Nipper6. Tweezers7. Projector * Before you start: This process ...
Page 26 - -3 Disassemble Lamp
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-2 2-3 Disassemble Lamp Module 1. Loosen 2 screws (as red circle) on the Lamp Module.2. Take off the Lamp Module. 2-2 Disassemble Lamp Cover Module 1. Loosen 2 screws (as red circle) on the Lamp Cover.2. Disassemble the Lamp Cover Module.
Page 27 - -5 Disassemble Top; -4 Disassemble Top Cover
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-3 2-5 Disassemble Top Shielding 1. Unscrew 5 screws (as red circle) to disassemble the Top Shielding. 2-4 Disassemble Top Cover Module 1. Unscrew 2 screws (as red circle) from the Bottom Cover. 2. Remove the Top Cover Module. Note: - When you remov...
Page 28 - -6 Disassemble Front
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2- 2-6 Disassemble Front Cover and IR Sensor Board 1. Unplug 1 connector (as yellow square).2. Press two sides (as red arrows point) to unfasten 2 tenons (as green square).3. Remove the Front Cover. 4. Tear off the mylar (as blue square).5. Unscrew 2...
Page 29 - Please refer to the table as below for
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-5 2-7 Disassemble Main Board Module and IO Cover Module 1. Tear off 3M tape (as green square).2. Unplug 6 connectors (as yellow square).3. Unscrew 2 screws (as red circle). Please refer to the table as below for details of each connector. Item Male...
Page 31 - -8 Disassemble Engine
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-7 NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal. 7. Unscrew 4 hex screws (as blue circle).8. Separate the Main Board ...
Page 32 - -9 Disassemble Color; -10 Disassemble DMD Chip
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2- NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal. 2-9 Disassemble Color Wheel Module 1. Unscrew 2 screws (as red circle...
Page 33 - -12 Disassemble Focus; -11 Disassemble Zoom
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2- Zoom Ring Zoom Ring Fixed Holder 2-12 Disassemble Focus Ring 1. Unscrew 3 screws (as red circle) to disassemble the Focus Ring. Focus Ring 2-11 Disassemble Zoom Ring 1. Unscrew 2 screws (as red circle) to disassemble the Zoom Ring and Zoom Ring Fi...
Page 34 - -13 Disassemble System
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-10 4. Unscrew 4 screws (as blue circle) to separate System Fan and Fan Shielding. Note: - Take the Fan Module as the right gesture. Fan Shielding System Fan 2-13 Disassemble System Fan Module 1. Unscrew 3 screws (as red circle) to disassemble the F...
Page 35 - -14 Disassemble Blower
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-11 2-14 Disassemble Blower 1. Unscrew 3 screws (as red circle).2. Disassemble the Blower. 2-15 Disassemble LVPS Module 1. Unplug 2 connectors (as yellow square).2. Unscrew 6 screws (as red circle).3. Disassemble the LVPS Module and the AC Inlet Bra...
Page 36 - -16 Disassemble Lamp
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-12 2-16 Disassemble Lamp Driver Module 1. Unscrew 1 screw (as red circle) to disassemble the Lamp Driver Module.2. Unscrew 2 screws (as blue circle). 3. Unplug 3 connectors (as green square) to disassemble the cables from Lamp Driver Module.4. Unsc...
Page 37 - -17 Disassemble Interrupt; -18 Disassemble Bottom
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-13 2-17 Disassemble Interrupt Switch 1. Unfasten 2 tenons (as green square) to disassemble the Interrupt Switch. 2-18 Disassemble Bottom Shielding 1. Tear off the EMI tapes (as yellow square).1. Unscrew 2 screws (as red cricle) to disassemble the B...
Page 38 - -19 Disassemble Speaker
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-1 2-19 Disassemble Speaker (for X1261/H5360) 1. Unfasten 2 tenons (as green square) as blue arrows point to disassemble the Speaker. 2-20 Rod Adjustment 1. Environment Adjustment - The distance between the engine and the screen is 2.38 M. - This pr...
Page 39 - Lamp Usage Hour
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-15 2-21 Re-write System and Lamp Usage Hour 1. Get into Service Mode - Press "Power", "Left", "Left" and "Menu" buttons sequentially to get into Service Mode.2. Get into Other Settings Mode - Use "Up" or "...
Page 40 - -22 Assemble Speaker
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-16 4. Re-write Lamp Hours (Full power mode) - Select "Lamp Hours Adjust" and use "Left" or "Right" buttons to re-write the "Lamp Hours (full)".5. Re-write Lamp Hours (ECO mode) - Select "Lamp Hours" and use &...
Page 41 - -23 Assemble Bottom
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-17 2-23 Assemble Bottom Shielding 1. Screw 2 screws (as red circle) to assemble the Bottom Shielding.2. Stick the EMI tapes (as yellow square). 2-24 Assemble Interrupt Switch 1. Fasten 2 tenons (as green square) to assemble the Interrupt Switch.
Page 42 - -25 Assemble Lamp Driver
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-1 2-25 Assemble Lamp Driver Module 1. Screw 4 screw (as yellow circle) to assemble the Lamp Driver Module and Lamp Driver Holder. 2. Plug 3 connectors (as green square) to assemble the cables on Lamp Driver Module. 3. Screw 2 screws (as blue circle...
Page 43 - -26 Assemble LVPS Module
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-1 2-26 Assemble LVPS Module 1. Plug 1 connector (as green square).2. Assemble the LVPS Module and the AC Inlet Bracket.3. Screw 6 screws (as red circle).4. Plug 2 connectors (as yellow square). 2-27 Assemble Blower 1. Assemble the Blower.2. Screw 3...
Page 44 - -28 Assemble System
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-20 2-28 Assemble System Fan Module 1. Screw 4 screws (as blue circle) to assemble System Fan and Fan Shielding. 2. Assemble the System Fan Module.3. Stick the EMI tape (as green square).4. Screw 3 screws (as red circle) to assemble the Fan Module.
Page 45 - -29 Assemble Focus Ring; -30 Assemble Zoom Ring
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-21 2-29 Assemble Focus Ring 1. Screw 3 screws (as red circle) to assemble the Focus Ring. 2-30 Assemble Zoom Ring 1. Screw 2 screws (as red circle) to assemble the Zoom Ring and Zoom Ring Fixed Holder.
Page 46 - -31 Assemble DMD Chip; -32 Assemble Color Wheel
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-22 2-31 Assemble DMD Chip and DMD Board 1. Rotate the screw (as yellow circle) 180° clockwise to assemble the DMD Board and DMD Chip. 2. Screw 2 screws (as red circle) to assemble the Heat Sink and DMD Module. Note: - Avoid touching the DMD Chip. -...
Page 47 - -33 Assemble Engine
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-23 2-33 Assemble Engine Module 1. Screw 4 screws (as yellow circle) to assemble the Engine Module.2. Stick the EMI Gasket (as green square). 2-34 Assemble IO Cover and Main Board Module 1. Assemble the IO Cover and Main Board Module.2. Screw 4 hex ...
Page 49 - -35 Assemble IR Sensor
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-25 2-35 Assemble IR Sensor Board and Front Cover 1. Assemble the IR Sensor Board and IR Cap.2. Screw 2 screws (as red circle).3. Stick the mylar (as blue square). 4. Assemble the Front Cover.5. Press two sides (as red arrows point) to fasten 2 teno...
Page 50 - -36 Assemble Top Shielding; -37 Assemble Top Cover
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-26 2-36 Assemble Top Shielding 1. Screw 5 screws (as red circle) to assemble the Top Shielding. Note: Avoid pressuring the Speaker cable (as yellow square) when you assemble the Top shielding. (for X1261/H5360) 2-37 Assemble Top Cover Moudle 1. Ass...
Page 51 - -38 Assemble Lamp
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 2-27 2-38 Assemble Lamp Moudle 1. Assemble the Lamp Module.2. Tighten 2 screws (as red circle) on the Lamp Module. 2-39 Assemble Lamp Cover Module 1. Assemble the Lamp Cover Module.2. Tighten 2 screws (as red circle) on the Lamp Cover.
Page 52 - Chapter 3; Troubleshooting; -1 LED Lighting Message; Message
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 3-1 Chapter 3 Troubleshooting 3-1 LED Lighting Message Message Power LED Red Blue Input Power Plug Flash ON to OFF 100ms -- Standby V -- Power button ON -- V Lamp retry -- 0.5 second H(On), 0.5 second L(Off) flashing Power off (Cooling state) 0.5 sec...
Page 57 - Chapter 4; Function Test & Alignment Procedure; -1 Test Equipment Needed
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 4-1 Chapter 4 Function Test & Alignment Procedure 4-1 Test Equipment Needed - IBM PC with SVGA/XGA resolution - DVD player with Multi-system, equipped "Component", "S-Video","Composite" and "HDMI".- HDTV Source (48...
Page 60 - Frequency and tracking boundary
Confidential 4-4 X1161/X1261/X1161A/X1161N/X110/H5360 4-6 PC MODE Note: - When getting into function test, adjust the zoom ring and focus ring to guarantee the image maximum and clearest, then start to test. - Test signal: analog 800 x 600 @60Hz (for X1161); analog 1024 x 768 @60Hz (for X1261); anal...
Page 62 - Color performance
Confidential 4-6 X1161/X1261/X1161A/X1161N/X110/H5360 - Ref. Defect specification table 6. Focus test Procedure - Test equipment: video generator - Test signal: analog 1024 x 768 @60Hz - Test pattern: Full screen Inspection item - Focus check Criteria - From screen 2.38 M via visual to check the foc...
Page 64 - G Sensor Calibration
Confidential 4-8 X1161/X1261/X1161A/X1161N/X110/H5360 (1) Calibration pattern should be in full screen mode. (2) Please press "Power", "Left", "Left" and "Menu" buttons sequentially to get into Service Mode. (3) Choose "Analog Settings", press “Menu” button to...
Page 65 - -8 Video Performance
Confidential 4- X1161/X1261/X1161A/X1161N/X110/H5360 4-8 Video Performance 1. CVBS Procedure - Test equipment: DVD player - Test signal: CVBS Inspection item - Video performance test Inspection Distance - 1.8 M ~2.5 M Criteria - Check any abnormal color, line distortion or any noise on the screen. 2...
Page 66 - -9 Optical Performance Measure
Confidential 4-10 X1161/X1261/X1161A/X1161N/X110/H5360 - Adjust the volume to maximum by using the remote controller. - Check the sound from speaker. - Check if the "mute" is normal. 5. HDMI Test (for H5360) Procedure - Test Signal : 720p,1080i - Test Pattern : Any Pattern - Equipment: DVD P...
Page 69 - Chapter 5; Firmware Upgrade
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 5-1 Chapter 5 Firmware Upgrade 5-1 Equipment Needed Software: (DDP 2430 for X1161/X1261/X1161A/X1161N/X110) (DDP 2431 for H5360) - DLP Composer Lite 9.2- Firmware (*.img)- Library file (X1161 X1261 FlashDeviceParameters) (library file has to put in P...
Page 70 - -2 DLP Composer Lite Setup
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 5-2 5-2 DLP Composer Lite Setup Procedure 1. Choose "DLP Composer Lite V9.2 Setup" Program. 2. Click "Next". 3. Read "License Agreement". - Choose "I accept and agree to be bound by all the terms and conditions of this Lic...
Page 72 - -3 USB Driver Upgrade
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 5-4 5-3 USB Driver Upgrade Procedure (for X1161/ X1161A/X1161N/X110) 1. Set-up - Hold on "power" button and plug in the power cord. - The power LED lights red and blue simultaneously after 5 seconds, then loosen "power" button. - Conn...
Page 73 - -4 Firmware Upgrade Procedure
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 5-5 5-4 Firmware Upgrade Procedure 1. Set-up - Hold on "power" button and plug in the power cord. - The power LED lights red and blue simultaneously after 5 seconds, then loosen "power" button. - Connect projector with PC by RS232 cab...
Page 76 - -5 Waveform Download
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 5-8 5-5 Waveform Download - Hold on "power" button and plug in the power cord.- After 2 seconds, the power LED will flash blue, then loosen "power" button.- After 5 seconds, the projector will automatically get into standby status. - ...
Page 77 - Chapter 6; EDID Upgrade; -1 EDID Introduction
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 6-1 Chapter 6 EDID Upgrade 6-1 EDID Introduction Extended Display Identification Data is a VESA standard data format that contains basic information about a display device and its capabilities, including vendor information, maximum image size, color ...
Page 78 - Software
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 6-2 6-2 Equipment Needed Software - EDID Program - EDID File (*.ini) Hardware - Projector - Power Cord for Projector (42.53506G002)- VGA Cable (42.87305G102)- HDMI(M) to DVI(F) Adapter (42.82B13G001) (for H5360)- DVI Cable (42.83N06G001) (for H5360)-...
Page 82 - -5 Un-lock SNID and Default Language Reset
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential 6-6 6-5 Un-lock SNID and Default Language Reset (1) Hold on "power" button then plug in the power cord. Note: At this moment, power LED flashes red or blue altemately about 2 seconds, then the power LED flashes blue, then loosen "power...
Page 89 - Front Module
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential V Front Module Item P/N Description Parts Supply 1 51.88T24G001 FRONT R CAP FOR X1160E 2 80.8CP05G001 PCBA IR SENSOR BD FOR X1161 V 3 51.8CP09H001 FRONT COVER MN3600H X1161 V 4 85.3A122G040 SCREW CAP MECH M2*4 Ni 5 61.8CP14H001 ACER LOGO FOR X1161 V ...
Page 94 - Bottom Shielding Module
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential X Bottom Shielding Module Item P/N Description Parts Supply 1 61.8CP06G001 BOTTOM SHIELDING SECC X1161 2 61.8CP08G001 SPEAKER BRKT SUS301 X1161 3 49.8CQ01G001 SPEAKER 2W 16OHM DAB128 90mm X1261 V 4 52.8CP05G001 SPONGE SPEAKER X1161
Page 97 - Engine Module
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential XV Engine Module Item P/N Description Parts Supply 1 70.8CP09G001 ASSY OPTICAL ENGINE MODULE Z15 (S450) (for X1161) 1 70.8CQ02G001 ASSY OPTICAL ENGINE MODULE (for X1261) 2 51.8CP04H001 FOCUS RING MN3600H X1161 V 3 51.8CP08H001 ZOOM RING MN3600H X1161...
Page 98 - Assy Engine Module
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential XV Assy Engine Module
Page 100 - Assy Color Wheel Module Z15
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential XV Assy Color Wheel Module Z15 Item P/N Description Parts Supply 1 61.8CP03G001 CW BRACKET SECC X1161 2 80.8CP04G001 PCBA PHOTO SENSOR BOARD FOR X1161 V 3 23.8EF19G001 YO 6S R81Y41G84C31W52B71_HE3 CW 4 85.1A126G040 SCREW PAN MECH M2.6*4 Ni 5 51.82Y29...
Page 101 - Assy Lamp Driver Module
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential XX Assy Lamp Driver Module Item P/N Description Parts Supply 1 51.88T11G003 HOLDER LAMP DRVER FOR H5350 2 75.8BA01G002 ASSY OSRAM LAMP DRIVER O6 MIC 180W (Gen5_Panyu+E20.8) V 3 85.1A123G060 SCREW PAN MECH M3*6 NI 4 85.3A122G040 SCREW CAP MECH M2*4 Ni...
Page 104 - Appendix B; I. Serial Number System Definition; Serial Number Format for Projector (take X1261 for example)
Confidential X1161/X1261/X1161A/X1161N/X110/H5360 I Appendix B I. Serial Number System Definition Serial Number Format for Projector (take X1261 for example) EYK0201001 915 00000 59 0 1 1 2 3 4 5 6 1 : EYK0201001 = Part Number 2 : 915 = Date Code (ex:200 9 = 9, the fifteenth week of the year = 15) 3...
Page 105 - II. PCBA Code Definition; PCBA Code for Projector; A B; Vendor Code
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential II II. PCBA Code Definition PCBA Code for Projector A B XXX XXXXXXXXX CC XXX EEEE 1 2 3 4 5 6 7 1 : ID 2 : Vendor Code 3 : Firmware Version 4 : P/N 5 : MB version 6 : Date Code 7 : S/N
Page 106 - General command type (Projector “receives” commands)
Confidential X1161/X1261/X1161A/X1161N/X110/H5360 I Appendix C RS232 function command summary table (for X1261/H5360) General command type (Projector “receives” commands) No Code (character) Function feature 1 OKOKOKOKOK\r Power On 2 * 0 IR 001\r Power On 3 * 0 IR 002\r Power Off 4 * 0 IR 004\r Keys...
