Page 3 - Information for your safety and; Safety instructions; Cleaning your monitor; Special notes on LCD monitors
iii Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off th...
Page 4 - Accessibility; Warnings; Using electrical power
iv Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet. Safe listening To protect yo...
Page 5 - Product servicing
v ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. • Do not overload a power outlet, strip or receptacle by plugging in ...
Page 6 - Potentially explosive environments; Additional safety information; Disposal instructions
vi Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Potentially explosive environments Switch o...
Page 7 - LCD pixel statement; Tips and information for comfortable use
vii Nevertheless, some pixels may occasionally misfire or appear as black or red dots. This has no effect on the recorded image and does not constitute a malfunction. This product has been shipped enabled for power management: • Activate display’s Sleep mode within 15 minutes of user inactivity. • A...
Page 8 - Developing good work habits
viii Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain.Eyes •...
Page 9 - or Blank
Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference ...
Page 10 - Declaration of Conformity; ecodesign requirements for energy-related product.; Ma; Easy Lai /Manager
Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih Taipei Hsien 221, Taiwan 4 3 2 1 - 6 9 6 2 - 2 - 6 8 8 : l e T 5 3 5 3 - 6 9 6 2 - 2 - 6 8 8 : x a F Declaration of Conformity We, Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan Contact Person: Mr. Easy ...
Page 11 - Contents
Information for your safety and comfort iii Safety instructions iiiiii Cleaning your monitor iii Connecting/disconnecting the device iii Accessibility iv Safe listening iv Warnings iv Using electrical power iv Product servicing v Additional safety information vi IT Equipment Recycling Information vi...
Page 12 - Troubleshooting
Page 13 - lis; Unpacking
1 En g lis h Unpacking Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future. Quick start guide D-sub cable Audio Cable User guide HDMI cable Adapter AC Power cord LCD monitor AC (Opti...
Page 15 - Screen position adjustment
3 En g lis h Screen position adjustment To optimize the viewing position, you can adjust the monitor tilt, using both of your hands to hold the edges of the monitor. The monitor can be adjusted to 15 degrees up or 5 degrees down. Connecting the adapter and AC Power code • Check first to make sure th...
Page 16 - English; Connector pin assignment; 5-pin color display signal cable
4 English Display Data Channel (DDC) To make installation easier, so long as your system supports the DDC protocol, the monitor is able to plug-and-play. The DDC is a communication protocol through which the monitor automatically informs the host system about its capabilities; for example, supported...
Page 17 - 9-pin color display signal cable
5 Eng lis h PIN No. Description PIN No. Description 1 TMDS Data2+ 2 TMDS Data2 Shield 3 TMDS Data2– 4 TMDS Data1+ 5 TMDS Data1 Shield 6 TMDS Data1– 7 TMDS Data0+ 8 TMDS Data0 Shield 9 TMDS Data0– 10 TMDS Clock+ 11 TMDS Clock Shield 12 TMDS Clock– 13 CEC 14 Reserved (N.C. on device) 15 SCL 16 SDA 17 ...
Page 18 - Standard timing table
6 English Standard timing table 1 640x480 60 Hz 2 640x480 72 Hz 3 640x480 75 Hz 4 MAC 640x480 66.7 Hz 5 VESA 720x400 70 Hz 6 800x600 56 Hz 7 800x600 60 Hz 8 800x600 72 Hz 9 800x600 75 Hz 10 MAC 832x624 74.55 Hz 11 1024x768 60 Hz 12 1024x768 70 Hz 13 1024x768 75 Hz 14 MAC 1152x870 75 Hz 15 VESA 1152x...
Page 19 - Installation; Steps
7 En g lis h Installation To install the monitor on your host system, please follow the steps below: Steps 1 Connect the video cablea Make sure both the monitor and computer are switched off. b Connect the VGA video cable to the computer. c Connect the digital cable (1) Make sure both the monitor an...
Page 20 - Users controls; Base controls
8 En g lis h Users controls Base controls Icon Item Description Power button/indicator Turns the monitor on/off. indicates power on. Amber indicates standby/power saving mode. Minus / Plus If the OSD is active, press the Minus or Plus buttonsto toggle between the OSD options. OSD functions Press to ...
Page 21 - Acer eColor Management; Operation instructions
9 Eng lis h Acer eColor Management Operation instructions 1 Press the Empowering Key to open the Acer eColor Management OSD and access the scenario modes. 2 Press " " or " " t o select the mode. 3 Press the Auto-adjust button to confirm the mode and exit Acer eColor Management. Featu...
Page 22 - Adjusting the OSD settings; Adjusting the picture quality
10 Eng lis h Adjusting the OSD settings Note: The following content is for general reference only. Actual product specifications may vary. Press the Menu key to open the OSD. You can use the OSD to adjust the picture quality, OSD position and general settings. For advanced settings, please refer to ...
Page 23 - Adjusting the OSD position
11 English Adjusting the OSD position 1 Press the Menu key to bring up the OSD. 2 Using the directional keys, select OSD from the onscreen display. Then navigate to the feature you wish to adjust.
Page 24 - Adjusting the setting
1 2 Eng lis h Adjusting the setting 1 Press the Menu key to bring up the OSD. 2 Using the keys, select Setting from the OSD. Then navigate to the feature you wish to adjust. 3 The Setting menu can be used to adjust the screen Menu Language and other important settings. /
Page 25 - Product information
1 3 English Product information 1 Press the Menu key to bring up the OSD. 2 Using the keys, select Information from the OSD. Then the basic / information of LCD monitor will show up for current input.
Page 26 - Blue
1 4 Eng lis h Troubleshooting troubleshooting list below to see if you can self-diagnose the problem. VGA mode Problem LED status Remedy No picture visible Using the OSD, adjust brightness and contrast to maximum or reset to their default settings. Off Check the power switch. Check if the power cord...
Page 27 - HDMI mode
15 Eng lis h Problem LED status Remedy No picture visible Using the OSD, adjust brightness and contrast to maximum or reset to their default settings. Off Check the power switch. Check if the AC power cord is properly connected to the monitor. Amber Check if the video signal cable is properly connec...
