Page 3 - Information for your safety and; Safety instructions; Cleaning your monitor; Connecting/disconnecting the device
iii Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a pr...
Page 4 - Accessibility; Warnings; Using electrical power
iv Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet. Safe listening To protect yo...
Page 5 - Product servicing
v ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. • Do not overload a power outlet, strip or receptacle by plugging in ...
Page 6 - Additional safety information
vi Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Potentially explosive environments Switch o...
Page 7 - LCD pixel statement; Tips and information for comfortable use
vii Mercury advisory For projectors or electronic products containing an LCD/CRT monitor or display:lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the Electronic Industries Alliance at www.eiae....
Page 9 - Declaration of Conformity
ix • using a glare-reduction filter • using a display visor, such as a piece of cardboard extended from the display's top front edge • Avoid adjusting your display to an awkward viewing angle. • Avoid looking at bright light sources, such as open windows, for extended periods of time. Developing goo...
Page 11 - Contents
Information for your safety and comfort iii Safety instructions iii Special notes on LCD monitors iii Cleaning your monitor iii Connecting/disconnecting the device iii Accessibility iv Safe listening iv Warnings iv Using electrical power iv Product servicing v Additional safety information vi IT Equ...
Page 13 - Unpacking
1 Eng lis h Unpacking Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future. LCD monitor User guide Quick start guide D-sub cable DVI cable AC power cord
Page 14 - Attaching the base
2 English Attaching the base Note: Remove the monitor and monitor base from its packaging. Carefully place the monitor face-down on a stable surface -- use a cloth to avoid scratching the screen. 1 Attach the the monitor stand arm to the base. 2 Ensure that the base is locked onto the monitor stand ...
Page 15 - Screen position adjustment
3 Eng lis h Screen position adjustment To optimize the viewing position, you can adjust the monitor tilt, using both of your hands to hold the edges of the monitor. The monitor can be adjusted to 15 degrees up or 5 degrees down. Connecting the power cord • Check first to make sure that the power cor...
Page 16 - Connector pin assignment; 5-pin color display signal cable
4 English Display Data Channel (DDC) To make installation easier, so long as your system supports the DDC protocol, the monitor is able to plug-and-play. The DDC is a communication protocol through which the monitor automatically informs the host system about its capabilities; for example, supported...
Page 17 - 9-pin color display signal cable
5 Eng lis h 19-pin color display signal cable 11 TMDS data 1/3 shield 23 TMDS clock+ 12 NC 24 DDC TMDS clock- PIN No. Description PIN No. Description 1 TMDS Data2+ 2 TMDS Data2 Shield 3 TMDS Data2– 4 TMDS Data1+ 5 TMDS Data1 Shield 6 TMDS Data1– 7 TMDS Data0+ 8 TMDS Data0 Shield 9 TMDS Data0– 10 TMD...
Page 18 - Standard timing table
6 English Standard timing table 1 640x480 60 Hz 2 640x480 72 Hz 3 640x480 75 Hz 4 MAC 640x480 66.7 Hz 5 VESA 720x400 70 Hz 6 800x600 56 Hz 7 800x600 60 Hz 8 800x600 72 Hz 9 800x600 75 Hz 10 MAC 832x624 74.55 Hz 11 1024x768 60 Hz 12 1024x768 70 Hz 13 1024x768 75 Hz 14 MAC 1152x870 75 Hz 15 VESA 1152x...
Page 19 - Installation; DVI
7 Eng lis h Installation To install the monitor on your host system, please follow the steps below: Steps 1 Connect the video cablea Make sure both the monitor and computer are switched off. b Connect the VGA video cable to the computer. c Connect the digital cable.(1) Make sure both the monitor and...
Page 20 - Users controls; Front panel controls
8 English Users controls Front panel controls Icon Item Description Power button/indicator Turns the monitor on/off. Red indicates power on. Pulsating red indicates standby/power saving mode. Minus / Plus If the OSD is active, press the Minus or Plus buttons to toggle between the OSD options. OSD fu...
Page 21 - Acer eColor Management; Operation instructions
9 Eng lis h Acer eColor Management Operation instructions 1 Press the Empowering Key to open the Acer eColor Management OSD and access the scenario modes. 2 Press " " or " " t o select the mode. 3 Press the Auto-adjust button to confirm the mode and exit Acer eColor Management. Featu...
Page 22 - Adjusting the OSD settings; Adjusting the picture quality
10 English Adjusting the OSD settings Note: The following content is for general reference only. Actual product specifications may vary. The OSD can be used for adjusting the settings of your LCD Monitor. Press the Menu key to open the OSD. You can use the OSD to adjust the picture quality, OSD posi...
Page 23 - Adjusting the OSD position
11 Eng lis h Adjusting the OSD position 1 Press the Menu key to bring up the OSD. 2 Using the directional keys, select OSD from the onscreen display. Then navigate to the feature you wish to adjust.
Page 24 - Adjusting the setting
12 English Adjusting the setting 1 Press the Menu key to bring up the OSD. 2 Using the keys, select Setting from the OSD. Then navigate to the feature you wish to adjust. 3 The Setting menu can be used to adjust the screen Menu Language and other important settings. /
Page 25 - Product information
13 Eng lis h Product information 1 Press the Menu key to bring up the OSD. 2 Using the keys, select Information from the OSD. Then the basic information of LCD monitor will show up for current input. /
Page 26 - Troubleshooting; VGA mode
14 English Troubleshooting Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. VGA mode Problem LED status Remedy No picture visible Red Using the OSD, adjust brightness and contrast to maximum or reset to their defa...
