Page 3 - I n s t r u c t i o n s; Introduction
I n s t r u c t i o n s Introduction You are about to enjoy an advanced Cumulative and Lap memory professional digital quar tz stopwatch withadvanced timing features. Model AE602M100, AE760M100, AE790M500 & AE790M500DEC Stopwatch includes Time of day, DailyAlarm, Chronograph stopwatch, 100 or 50...
Page 4 - Recall - used for recalling recorded split and lap times
As you choose each "mode", a message will be displayed for a second before you enter the mode: Normal Time mode(All models) Alarm Time mode(All models) Chronograph mode(All models) Lap Time Recall mode(All models) Data mode(760M & 790M models only) The operation of the stopwatch is divid...
Page 5 - W E 1 - 3; year
This is only a brief description of these buttons. Detailed uses of the buttons are different in particular functionsand will be described later in the instructions. Pressing [MODE] button will toggle among the modes above. Note that there is no auto-return function in thestopwatch. Whenever you cha...
Page 6 - The hour digits may be displayed in 12hr or 24hr format.; S O U n d
or date-month (d-m), Sound ON or OFF, Contrast (darkness of the digits - default is 9), then back to Second,and recycles again. Note: when the second is to be set, press [START] to reset the second digits to zero. At the end of setting, press [RECALL] or [MODE] to exit from the setting mode and back...
Page 8 - The maximum memory counter value is 100 or 500.
Whenever the stopwatch stops running, the "STOP" indicator will be ON. Press the button [START/STOP] tostart the stopwatch. As it runs, the current elapsed time is shown on the lower line. To view the current split / lap time, you can press [LAP/SPLIT]. The number of split/lap times is shown...
Page 10 - Chronograph Data Recall Mode; Then comes the slowest lap time by further pressing of [RECALL].; R E C A L L
Please note that if the stopwatch has started running (or is running), no selection for chronographoperating modes can be made until the stopwatch has been stopped and reset. Segmented run memory for lap/split time storage:- A header consisting of the date/time stamp is attached to each segment to i...
Page 12 - F R E E
[RECALL] After recalling the first record, press [RECALL] once more to exit from Recall mode and go back to chronographmode. The "RECALL" icon will be OFF. [RECALL] During memory recall, you can press either [START], [STOP] or [LAP/SPLIT] to exit from chrono recall modeand jump to the chrono...
Page 13 - How to delete individual memory segments:-; d E L E T E
The header consisting of the date/time stamp will be shown. The number of laps in the segment will appearin the upper left while the segment number is displayed in the middle left. If the segment shown is not yourdesired segment, press [START] to reach the desired segment. The current segment will b...
Page 14 - Timer Mode
How to delete all memory segments:- Instead of deleting one segment, you can also delete all memory segments. When you enter the Data mode,you see the screen "FREE XXX LAP". Press and hold the [RESET] for 3 seconds. You will hear "Beep, beep,beep" for 3 seconds, then a long "Beep...
Page 15 - How to set the timer; CR
Under CS operation mode, the timer, after counting down to 0:00'00", will stay at 0:00'00"0 until you press[RESET] to reload the timer value. Under CU operation mode, the timer, after counting down to 0:00'00"0, will count up and stop at 19:59'59"9. How to set the timer Press and hol...
Page 16 - P A C E R
Pacer Mode Press [MODE] until you enter the Pacer mode. In the Pacer mode, you can set the standard pacer speed from5 to 240 beats per minute in the following values:5, 10, 20, 30, 40, 50, 60, 80, 100, 120, 150, 180, 200, 240 In Pacer mode, the display will be:- The digits are flashing to indicate t...
Page 17 - At the end of the first second, the display will become steady.; S T R O k E
In the Stroke Measurement mode, the duration of 3 strokes is taken and the stroke frequency (counts perminute) is calculated. As the stroke frequency falls out of the range of 10 - 180, "Err" will appear to show theerror condition. Press [START] to start the measurement. During the 1st secon...
Page 18 - Distance Setting; As an example, the distance is set at 400m.; Speed Mode Running
Distance Setting Press [RECALL] for 2 seconds to enter setting mode, the unit icon flashes. Press [START] to toggle between KM and MILE. To select the following digits, press [RESET]. The far rightdigit will blink and you can set the distance from the least significant digit to the most significant ...
Page 20 - Lap Time & Speed Recall
Lap Time & Speed Recall Similar to the Chrono Recall mode, during speed measurement or Stop state, you can press [RECALL] torecall the speed/lap memories. The Mode message will be shown for one to two seconds as the Modemessage display is displayed. The Speed and Lap time will be displayed on th...