Abocom FE1000 - Manual - manualsarea.com

Page 2 - HARDWARE INSTALLATION; Please refer to; Software Installation; on how to

HARDWARE INSTALLATION This chapter describes how to install the dual speeds Fast Ethernet PC Card in your notebook computer and connect it to network. The PC Card could be connected to either 100Mbps Fast Ethernet or 10Mbps Ethernet over unshielded twisted pair (UTP) cable. The PC Card has the abili...

Page 3 - Connecting to the Network; For operation in

-2- Connecting and Removing the Cable of Media Coupler to the PC Card Grasp the PC Card 15-pins connector at the end of the media coupler with the pointing triangle facing upward. Gently insert it into the mating connector on the PC Card until it clicks in place at both sides. Attention should be pa...

Page 4 - For operation in the 10Mbps; LED Indicators

should be used to connect between media coupler and 100Mbps hub or switch. symbol 108 \f "Monotype Sorts" \s 6 O For operation in the 10Mbps (10Base-T) Ethernet network, Category 3, 4 or 5 unshielded twisted pair (UTP) cable could be used to connect between the media coupler and a 10Mbps hub...

Page 5 - SOFTWARE INSTALLATION; INSTALL; Novell Netware; Menu Installation

SOFTWARE INSTALLATION Plug the driver diskette into the floppy drive and set the current drive to the floppy drive. Then run INSTALL to install the real mode drivers such as ODI or NDIS 2.x or Packet Drivers into the target disk. Novell Netware There are two methods to install the Netware client ODI...

Page 6 - OK

3 .If current settings are acceptable, select Start Installation and go to step 5. Otherwise, select Modify Parameters to make settings changed 4 .Move cursor to focus on the setting you want to make change and press <Enter>” to select a fit value. When the configurations are set completely, p...

Page 7 - Hardware Specific Module; .A typical ODI workstation startup batch file

2 .Using a text editor to edit the NET.CFG for setting the default frame type. In the Netware server the frame type is set to 802.3 for NW3.11 and 802.2 for NW3.12 and NW4.x The frame type must be set to the same with the server or the client couldnsymbol 146 \f "Parisian BT" \s 10 ’} t logi...

Page 8 - Other Drivers

-Get the 4 Client disks from the network administrator, or -Run the \NWCLIENT\INSTALL.EXE in a previous Installation 2 .A message appears on the screen asking you whether or not you want the program to perform modifications on your AUTOEXEC.BAT and CONFIG.SYS files. 3 .Answer "Yes". The prog...

Page 9 - .Go to the Insert the Driver Disk dialog box and; Enter; and select the target ODI driver.; Link Driver LE100ODI; .Copy the file LANEN.EXE from the directory

10 .Go to the Insert the Driver Disk dialog box and specify the path where the ODI driver and INS files reside. For example: C:\ODI.DOS. 11 .Press Enter and select the target ODI driver. 12 .Specify the driver's optional settings. 13 .Press F10 to save to new configuration. 14 .Highlight "Instal...

Page 10 - .Run STARTNET to access the Novell network.; MS LAN Manager; on the installation

--Card Enabler SET NWLANGUAGE=ENGLISH --Set NetWare 4.X to English language LSL --Link Support Layer Module provided by Novell LE100ODI --Hardware Specific Module IPXODI --IPX Protocol Stack Module provided by Novell VLM --DOS Support Module provided by Novell F: --Change to connected device LOGIN x...

Page 13 - Packet Driver; Windows for Workgroups

DRIVERNAME = LE100NDS$ Packet Driver 1 .Run INSTALL.EXE from root directory of driver diskette. 2 .Select Packet Driver item on the menu screen. 3 .If current settings are acceptable, select Start Installation and go to step 5. Otherwise, select Modify Parameters ” to make setting changed. 4 .Move c...

Page 15 - Novell Netware Server

12 .If current settings are acceptable, select Start Installation ” and go to step 13. Otherwise, select Modify Parameters ” to make settings changed. 13 .Move cursor to focus on the setting you want to make a change and press <Enter> to select a fit value. When the configuration is set comple...

Page 16 - Windows 95 Installation

3 .Open My Computer 4 .Open Control Panel 5 .Run the Network 6 .Select Adapters page 7 .Press Add to add network adapter 8 .Press Have Disk button 9 .Insert the driver disk into drive A: 10 .Specify the path to ” A: \ and press OK 11 .A dialog box will appear to adjust the driver's settings. The res...

Page 17 - Artisoft Lantastic 6.0 Installation

2 .Insert the PC Card into the slot. In New Hardware Found dialog box, select Driver from disk provided by hardware manufacturer”. 3.Please input the path, A:\ and insert driver diskette. The driver will be installed and you may be asked for the original Windows 95 CD/disks. 4 .For the first time in...

Page 20 - click on the

1 .In the OS/2 Desktop group, double-click on the MPTS icon. 2 .Click on the Configure button. 3 .Select the LAN adapters and protocols option. 4 .Click on the Configure button. 5 .Select the Other adapters ...” option. 6 .Insert the driver diskette and type the driver path: A:\OS2\NDIS2 Click on th...

Abocom FE1000 - Manual

Table of Contents:

Summary

Other Abocom Models