3M 25127 - Manual

1

2

WARNING

• Never operate this tool without all safety features in place and in proper working order.
• Never over-ride or disable the safety features of the start-stop control such that it is in the on position.
• Make sure the tool is disconnected from its air source before servicing, inspecting, maintaining, cleaning, and before changing abrasive product.
• Prior to use, inspect abrasive product and accessories for possible damage. If damaged, replace with new abrasive product and accessories available from 3M.
• Only use accessories supplied or recommended by 3M.
• Use only with mounting hardware recommended by 3M; check with 3M for mounting hardware requirements.
• Always ensure that shaft diameters match internal diameters of the collet inserts.
• Maximum operating speed of abrasive products or accessories must be reduced whenever the exposed length of shaft (overhang) is longer than

corresponding 3M approved products.

• Always ensure that a minimum of 10mm shaft gripping length is observed.
• Never install and use router bits or cutting-off wheels in a die grinder tool (which is unguarded).
• Use only with abrasive products not requiring guards according to local, state and federal regulations.
• Never allow this tool to be used by children or other untrained people.
• Do not leave an unattended tool connected to air source.

To reduce the risk of all hazards associated with vibration:

• If any physical hand/wrist discomfort is experienced, work should be stopped promptly to seek medical attention. Hand, wrist and arm injury may result from

repetitive work, motion and overexposure to vibration.

To reduce the risks associated with loud noise:

• Always wear protection for eyes, ears, and respiratory protection while operating this product. Follow your employer’s safety policy for PPE’s and/or ANSI

Z87.1 or local/national standards for eyewear and other personal protective equipment requirements.

To reduce the risk associated with fire or explosion:
• Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. The abrasives are able to create sparks

when working material, resulting in the ignition of the flammable dust or fumes.

• Refer to MSDS of material being worked as to potential for creating fire or explosion hazard.

To reduce the risk associated with hazardous dust ingestion or eye/skin exposure:

• Use appropriate respiratory and skin protection, or local exhaust as stated in the MSDS of the material being worked on.

To reduce the risk associated with hazardous voltage:

• Do not allow this tool to come into contact with electrical power sources as the tool is not insulated against electrical shock.

CAUTION

To reduce the risk associated with skin abrasion, burns, cuts, or entrapment:

• Keep hands, hair, and clothing away from the rotating part of the tool.
• Wear suitable protective gloves while operating tool.
• Do not touch the rotating parts during operation for any reason.
• Do not force tool or use excessive force when using tool.

To reduce the risk associated with whipping or hazardous pressure-rupture:

• Ensure supply hose is oil resistant and is properly rated for required working pressure.
• Do not use tools with loose or damaged air hoses or fittings.
• Be aware that incorrectly installed hoses and fittings might unexpectedly come loose at any time and create a whipping/impact hazard.

To reduce the risk associated with fly off of abrasive product or parts:

• Use care in attaching abrasive product and mounting hardware; following the instructions to ensure that they are securely attached to the tool before use or

free-spinning.

• Never point this product in the direction of yourself or another person, or start tool unintentionally.
• Never over-tighten accessory fasteners.

Important Safety Information

Intended Use

3

Original Instructions

WARNING

MSDS

WARNING!

Read the Material Safety

Data Sheets (MSDS)

before using any materials.

Contact the suppliers of the

workpiece materials and

abrasive materials for copies

of the MSDS if one is not

readily available.

Exposure to DUST generated from

workpiece and/or abrasive materials

can result in lung damage and/or other

physical injury.
Use dust capture or local exhaust as

stated in the MSDS. Wear government-

approved respiratory protection and eye

and skin protection.
Failure to follow this warning can

result in serious lung damage and/or

physical injury.

Die Grinder INSTRUCTIONS MANUAL

8,000 RPM 1/4 in (6 mm) Collet 1 HP, 12,000 RPM 1/4 in (6 mm) Collet 1 HP,

18,000 RPM 1/4 in (6 mm) Collet 1 HP, 20,000 RPM 1/4 in (6 mm) Collet 1 HP,

4,000 RPM 1/4 in (6 mm) Collet 0.5 HP, 18,000, RPM 1/4 in (6 mm) Collet

0.5 HP, Extended 18,000 RPM 1/4 in (6 mm) Collet 0.5 HP

Please read, understand and follow all safety information contained in these instructions prior to the use of this tool.
Retain these instructions for future reference.

This pneumatic tool is intended for use in industrial locations, and used only by skilled, trained professionals in accordance with the instructions in this manual.
This pneumatic tool is designed to be used with a disc pad and abrasive disc or other shaft mounted abrasive product for sanding metals, wood, stone, plastics
and other materials. It should only be used for such sanding applications and within its marked capacity and ratings. Only accessories specifically recommended
by 3M should be used with this tool. Use in any other manner or with other accessories could lead to unsafe operating conditions.

Do not operate tool in water or in an excessively wet application.
Do not use abrasive products that have a Max RPM less than the RPM rating marked on the tool.

Explanation of Signal Word Consequences

WARNING:

Indicates a potentially hazardous situation which, if not avoided, may result in death or serious injury and/or property damage.

CAUTION:

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or property damage.

To reduce the risks associated with impact from abrasive product or tool breakup, sharp edges, hazardous pressure, rupture, vibration and noise:

• Read, understand and follow the safety information contained in these instructions prior to the use of this tool. Retain these instructions for future reference.
• Only personnel who are properly trained should be allowed to service this tool.
• Practice safety requirements. Work alert, have proper attire, and do not operate tool under the influence of alcohol or drugs.
• Operators and other personnel must always wear protection for eyes, ears, and respiratory protection when in the work area or while operating this

product. Follow your employer’s safety policy for PPE’s and/or ANSI Z87.1 or local/national standards for eyewear and other personal protective equipment
requirements.

• Wear protective apparel, taking into consideration the type of work being done.
• Never exceed marked maximum input pressure (90psi / .62Mpa / 6.2Bars).
• Proper eye protection must be worn at all times.
• Tool shall not be operated in the presence of bystanders.
• If you notice any abnormal noise or vibration when operating the product, immediately discontinue its use and inspect for worn or damaged components.

Correct or replace the suspect component. If abnormal noise or vibration still exists, return the tool to 3M for repair or replacement. Refer to warranty
instructions.