3M 2220M - Manual

3 Quick Start Transmitter Battery Installation Transmitter Overview Dynatel ™ 220M Off On Frequency Output Level Hz ƒ Induction Direction ➊ ➋ ➎ ➌ ➍ 1.. . Power OFF / Battery Level Indicator –.Press.and.hold.. Display.reads:.“OK”.with.solid.tone.=.good..“LO”.with.pulsing.tone.=.low..“-.-”.with.no.ton...

4  Warning Potential for electric shock exists when handling connection cables while the transmitter is ON. Make all connections prior to powering on the unit. Turn the transmitter OFF before handling connection cables.  Warning Voltage greater then 240 volts will damage equipment and could cause ...

5 Receiver Overview ➊ ➋ ➌ ➍ ➎ ➏ ➐ ➑ ➒ 1.. . Volume Control –.Adjusts.the.volume.of.the.receiver.through.three.levels.of. audio.and.off. 2.. Power Key –.Powers.the.receiver.on.and.off. 3.. . Peak Key –.Toggles.between.Directional.Peak.and.Single.Peak.antenna. configuration. 4.. . Line Locate Key –.Pl...

6 Transmitter Operations There.are.three.different.methods.of.applying.the.transmitter’s.locating.signal.to.the.target.conductor:.Direct.Connection,.3M ™ .Dynatel ™. Dyna-Coupler.Clamp,. and.Induction. Direct Connection This.is.the.preferred.mode.of.operation.because.the.transmitter.is.connected.dir...

7 Induction Method If.you.cannot.make.a.direct.connection,.or.use.the.3M ™ .Dynatel ™ .Dyna-Coupler. clamp.to.apply.a.locating.signal.on.the.target,.use.the.induction.method..This.method.uses.the.internal.coil.of.the.transmitter.to.generate.a.magnetic.field..This.is.the.least.preferred.method.of.app...

8 Receiver Operations Initial Settings From.the.manufacturing.facility,.the.receiver.is.configured.as.follows:. Line Locate Frequencies Selection Default 8 kHz Always Enabled Enabled 8 kHz Always Enabled Enabled Power Always Enabled Enabled Radio Enable/Disable Disabled CATV Enable/Disable Disabled ...

Line Locating Screen ➊ ➋ ➌ ➐ ➍ ➎ ➏ ➑ 1.. Speaker Icon .–.Indicates.audio.level 2.. Bar graph –.Graphical.representation.of.received.signal 3.. Peak Mode Indicator .–.Indicates.single.or.directional.peak.mode 4.. . Selected Line Locating Frequency .–.Displays.the.frequency.the.receiver. will.detect 5...

4 Pin-Pointing the Sonde Note: The receiver handle must be oriented perpendicular to the sonde. The cross bar of the receiver must be in line with the sonde (the opposite of line locating) . 1.. .Set.the.receiver.to.Sonde.mode.by.pressing.the.Sonde.key.until.the. frequency.of.the.sonde.appears.on.th...

5 Specifications Receiver Locating Modes Special (Single) Peak, Dual Peak w/Direction, Depth & Current Gain Adjustment Automatic with Manual override Frequencies Active Passive Power Passive LF Passive CATV Cathodic Protection Auxiliary/Sonde (Receive only) 8 kHz, 8 kHz 50 Hz or 60 Hz VLF 5 k – ...

6 Environmental Operating Temperature –4° F to ° F (–0° to 50° C) Storage Temperature –4° F to 58° F (–0° to 70° C) Standard IP54 Regulatory CE Physical Specification Size (H x W x D) in (cm) Weight (w/ batteries) Transmitter 6.75 x .5 x 7.75 (7. x 8.6 x .7) 5. lb (.4 kg) Receiver 0.5 x 0.5 x 30 (6....

7 CE Compliance Statement of Conformity “Hereby,.3M.declares.that.this.Underground.Locating.Product.is.in.compliance.with.the.essential.requirements.and.other.relevant.provisions.of.Directive.1999/5/EC.”www.3m.com/market/telecom/access/conformity/ Statement of Intended Use The.3M ™ .Dynatel ™ .Advan...