3Com 5000 - Manual

3Com 5000

3Com 5000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
Page: / 16

Table of Contents:

  • Page 2 – Backplane Type; Software Prerequisites; Before you install a new SwitchModule:; Crucial Download Procedure; All bridge port communication ceases if
  • Page 3 – Installation Precautions; To ensure optical safety when you install
  • Page 4 – Unpacking Procedure; CLASS 1; Installing the SwitchModule; Power Requirement at
  • Page 6 – Basic Configuration Steps; Default Configuration After Installation; SwitchModule User Guide
  • Page 7 – CoreBuilder 5000 SwitchModule User Guide; Creating an Additional Virtual Bridge; NMS
  • Page 8 – Finding More Information; CoreBuilder 5000 SwitchModule User; Management Task
  • Page 9 – Common Front Panel Features; LED; 4-Port Ethernet Telco SwitchModule; XXXX
  • Page 10 – 0BASE-T SwitchModules use the following port types:
  • Page 11 – Ethernet Backplane Port
  • Page 12 – SwitchModule
  • Page 13 – 0BASE-T and FDDI Mixed Technology SwitchModule; LED State; Optical Bypass Connector
  • Page 14 – -Port FDDI SwitchModule; ports with MIC connectors.; 2-Port FDDI Concentrator SwitchModule; — Supports; Optical Bypass Connector; Port Status LED State
  • Page 16 – Com Corporation L; IMITED
Loading the manual

Part Number 10013592

®

CoreBuilder

®

5000 SwitchModule

Quick Start and Reference

1.0

Introduction

The 3Com CoreBuilder

®

5000 SwitchModule is a LAN

switching module for the CoreBuilder 5000 Integrated
System Hub. The SwitchModule is available in several
media configurations and in single-slot and dual-slot
models.

Before you unpack the SwitchModule, read Section 3.0,
"Installation Prerequisites" and Section 5.0, "Installation
Precautions".

WARNING:

CoreBuilder 5000 SwitchModules must

be installed only by trained service personnel.

2.0

Learning About SwitchModules

This document provides the basic information that you
need to install and configure a 3Com CoreBuilder 5000
SwitchModule at software Version v3.0.

For more detailed information about using the
SwitchModule, see the following documents:

■

CoreBuilder 5000 SwitchModule User Guide

■

CoreBuilder 5000 Distributed Management Module
User Guide

for software Version v6.00 or later

■

CoreBuilder 5000 Distributed Management Module
Commands Guide

for software Version v6.00 or later

You can view these documents online with the 3Com

DocsOnCD

documentation CD-ROM that comes with this

product.

To order hard-copy documents, contact your network
supplier, or call 3Com Corporation at 1-800-724-2447 and
choose the Customer Operations option.

3.0

Installation Prerequisites

Before you begin the SwitchModule installation process,
read the hardware and software requirements in this
section.

In addition to reading this document, be sure to
read the Release Note for CoreBuilder 5000
SwitchModules.

3.1

Tools Required

You need a flat-blade screwdriver to install the
CoreBuilder 5000 SwitchModule in the hub.

3.2

Hardware Prerequisites

1

Ensure that the CoreBuilder 5000 hub has at least one
of the following management modules installed:

■

6000M-MGT Distributed Management Module,
Version v6.00 or later

■

6000M-CMGT Advanced DMM/Controller Module,
Version v6.00 or later

2

Ensure that the CoreBuilder 5000 hub has the following
controller module installed: 6000M-RCTL Controller
Module, Version v1.15 or later

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Backplane Type; Software Prerequisites; Before you install a new SwitchModule:; Crucial Download Procedure; All bridge port communication ceases if

2 C ORE B UILDER ® 5000 S WITCH M ODULE Q UICK S TART AND R EFERENCE 3 Ensure that the CoreBuilder 5000 hub contains either a PacketChannel or a SwitchChannel backplane. To verify that the hub has one of these backplanes, enter the command SHOW HUB. The model number displayed in the Hub Type field s...

Page 3 - Installation Precautions; To ensure optical safety when you install

C ORE B UILDER ® 5000 S WITCH M ODULE Q UICK S TART AND R EFERENCE 3 For ease of reading and because the DMM and A/DMM are basically the same, the term DMM is used in this release note to refer to both modules. CAUTION: Do not upgrade to any later version until instructed to do so in Step 5. See the...

Page 4 - Unpacking Procedure; CLASS 1; Installing the SwitchModule; Power Requirement at

4 C ORE B UILDER ® 5000 S WITCH M ODULE Q UICK S TART AND R EFERENCE IEC 825, Class 1 LED Device. For connection only to Class 1 LED Devices. 6.0 Unpacking Procedure Follow this procedure to unpack a SwitchModule: 1 Verify that the SwitchModule is the model that you ordered by examining the model nu...

Other 3Com Models

All 3Com Other