3Com 3C17121 - Manual
3Com 3C17121 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Handling the Module; Installing the Module into a Switch; NSTALLATION
- Page 4 – ECHNICAL
- Page 5 – CSA Statement; EGULATORY
- Page 6 – EGAL
‘ roll
This guide covers the following products:
SuperStack
®
3 Switch 4300 10/100/1000BASE-T
Module (3C17121) provides one Ethernet port for
connection to your network.
SuperStack 3 Switch 4300 10/100/1000BASE-T Dual
Module (3C17122) provides two Ethernet ports for
connection to your network.
The procedures described in the User Guide assume that
you have a single port Module. If you have a Dual
Module the procedures are the same, except that
procedures relating to the port apply to each port on
the Dual Module.
The Module conforms to the full duplex implementation
of the Gigabit Ethernet standard, IEEE 802.3ab and has
an auto-negotiating 10/100/1000BASE-T port configured
as Auto MDI (crossover).
Alternatively, you can manually set the port to 10BASE-T
half duplex, 10BASE-T full duplex, 100BASE-TX half
duplex or 100BASE-TX full duplex. You can also
manually set the port to 1000BASE-T. The port uses
Category 5 copper cabling with an RJ-45 connector. The
maximum segment length is 100 m (328 ft) over
Category 5 twisted pair cable.
WARNING:
RJ-45 Ports. These are shielded RJ-45 data
sockets. They cannot be used as standard traditional
telephone sockets, or to connect the unit to a traditional
PBX or public telephone network. Only connect RJ-45
data connectors, network telephony systems, or network
telephones to these sockets. Either shielded or
unshielded data cables with shielded or unshielded
jackets can be connected to these data sockets.
LEDs
You can gather information about the status of the
Module and its packet activity using the Expansion
Module port LEDs on the front of the Switch.
Switch Front Panel LED’s
I
NTRODUCTION
Module Packet LED
Appearance
Color
Meaning
On
Green
Packets are being transmitted or received
on the Module port.
Off
No color
There are no packets being transmitted or
received on the Module port.
Module Status LED
Appearance
Color
Meaning
On
Green
The Module is installed.
Off
No color
There is no Module installed or an
unsupported Module is fitted.
Module Panel LED
Appearance
Color
Meaning
On
Green
The Port has a link and is running at the
speed indicated.
Off
No color
The Port does not have a link.
SuperStack
®
3 Switch 4300 10/100/1000BASE-T Module (3C17121)
and Dual Module (3C17122) User Guide
DUA1712-1AAA01
1000
10
100
3C17121 Super
Stack 3 Sw
itch 4300 1000BASE-
T
S/N:
XXXX/
7XXXXXXXXX
1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
WARNING : Installation and removal of the Module must be carried out by qualified personnel only. Before installing the Module into a unit, you must first disconnect the unit from the mains power supply. For full safety instructions, refer to the user guide that accompanies the unit. AVERTISSEMENT :...
The following options are available for technical support: In the first instance contact your Network Supplier Check the 3Com knowledgebase at http://knowledgebase.3com.com Browse the 3Com web site on http://www.3com.com Please have your product model name, part number, hardware revision numbe...
FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Thi...
