3Com 3500 - Manual
3Com 3500 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Table 1; System Site Requirements
- Page 3 – Quick Installation Guide; Before You Begin; Before you install the system:; Table 2; System Hardware Mounting Kit; Installing the system on a table top
- Page 4 – For installation instructions, see the; system display; in the
- Page 5 – Table 3; System Memory Configuration at Release 1.2 or Earlier; Frame Processor
- Page 6 – To get your system powered up and ready to operate:; Figure 1; System Power Receptacle; Insert the other end of the power cable into a power outlet.; Power Supply latch
- Page 7 – Table 4; System Diagnostics — System Processor LED Activity
- Page 8 – Getting Started Guide; Table 5; Management Access Mechanisms
- Page 9 – Defining a Management Interface; Implementation Guide; management ip interface define; interface; Command; ip interface define
- Page 10 – Getting
- Page 11 – Table 6; Troubleshooting Power Failures; System does not power up.
- Page 12 – Table 7; Troubleshooting Abnormal Status on System Processor LEDs
- Page 14 – Table 8; Troubleshooting Abnormal Activity on the Module Status LEDs
- Page 15 – Technical Support
Quick Installation Guide
For the CoreBuilder
®
3500 System
This guide provides quick installation procedures for the
CoreBuilder
®
3500 system. It is intended for the network administrator
who has experience installing communications equipment.
System Setup Tasks
To get your system and its components to the state at which you can
connect to your network, follow the setup tasks in the figure. If you need
more information on each setup task, see the related sections in this
guide or the complete details in the indicated documents.
RUN
SYS
INS
PS1
PS2
FAN
R
N
S
TEMP CONFIG
INS
PCMCI
MODEM
TERMINAL
ETHERNET
10BT
PWR
ERROR
R
Determine Site Requirements
•
Getting Started Guide,
Appendix C
•
Software Installation and
Release Notes
1
Administer and Operate
the System
•
Command Reference Guide and
Implementation Guide
(on the
Software and
Documentation CD)
11
Solve Problems
• This guide
•
Getting Started Guide, Chapter 7
10
Configure the System for
Management
•
Getting Started Guide, Chapter 6
9
Power Up the System
•
Getting Started Guide, Chapter 5
8
Attach Cables to the System
Processor and the Modules
•
Getting Started Guide, Chapter 4
• Module installation guides
7
Install Media Modules
• Module installation guides
6
Install the Additional
Power Supply (Optional)
•
Power Supply Assembly Removal
and Replacement Guide
4
Install the System on a
Table Top or in a Rack
•
Getting Started Guide,
Chapter 2
3
Unpack the CoreBuilder 3500
System
•
Unpacking Instructions
2
5
Install the Memory Upgrade
SIMMs for Systems at
Release 1.2 or Earlier
•
System Processor Memory
Upgrade Installation Guide
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Quick Installation Guide Installing the System To install the system in your network, follow the steps in this section. WARNING: For safety reasons and to ensure adequate cooling airflow, install blank faceplates over all empty slots. Install the system in an area that meets the requirements in Ta...
Quick Installation Guide 3 Before You Begin Before you install the system: ■ Move the system close to where you plan to install it, and close to a power receptacle. ■ Have a No. 2 Phillips screwdriver available. ■ Have the hardware kit available. See Table 2. Determine whether you are installing the...
4 Quick Installation Guide The system operates using a single power supply assembly and is shipped with one power supply installed. You can add a second power supply to the system. The additional power supply is orderable and shipped separately. WARNING: Removal or replacement of a power supply is t...
