3Com 100BASE-FX - Manual
3Com 100BASE-FX – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Front Panel; Figure 1; Front Panels for the 10/100BASE-TX and 100BASE-FX FEN Modules
- Page 3 – Audience Description; This guide is intended for; Safety Precautions; LED Safety Information:; CLASS 1
- Page 4 – When you handle a module, follow these precautions:
- Page 5 – Remove the module, in its antistatic bag, from the shipping box.
- Page 6 – CoreBuilder 9000 Release Notes for the Fast Ethernet and; Module Placement
- Page 8 – Table 1; Reserved for an SFM Not applicable
- Page 9 – Table 2
- Page 10 – Table 3
- Page 11 – Table 4; Reserved for an SFM
- Page 12 – Table 5
- Page 13 – Table 6
- Page 15 – Table 9
- Page 16 – Installing the Module; To install a FEN Switching Module:
- Page 17 – Figure 2; Installing a FEN Switching Module into a 7-Slot Chassis; screws
- Page 18 – Figure 3; Installing a FEN Switching Module into a 16-Slot Chassis; screw
- Page 20 – Table 11 describes LED colors and definitions.; Module and Port Status LED Indicators
- Page 21 – To manage the module from the Administration Console:; module baseline display; Web Management; For information about setting up your IP address, see the
- Page 23 – Safety; CE Mark; Emissions; FCC Part 15 Class A
- Page 25 – Com Corporation L; IMITED
- Page 27 – EMC D; UK
10-Port 100BASE-FX and
20-Port 10/100BASE-TX
Fast Ethernet Layer 2
Switching Modules
Quick Start Guide
For the CoreBuilder
®
9000 Enterprise Switch
Module Descriptions
This guide describes key installation information for two
CoreBuilder
®
9000 Fast Ethernet (FEN) Switching Modules:
■
The 10-port 100BASE-FX Fast Ethernet Layer 2 Switching Module
(Model Number 3CB9LF10MC) has ten 100 Mbps Ethernet fiber-optic
ports with SC connectors on its front panel and two 1-Gigabit ports
on the back for connection to the chassis backplane.
■
The 20-port 10/100BASE-TX Fast Ethernet Layer 2 Switching Module
(Model Number 3CB9LF20R) has twenty 10/100 Mbps RJ-45 ports on
its front panel and two 1-Gigabit ports on the back for connection to
the chassis backplane.
Each of these FEN Switching Modules operates as a Layer 2 switch and
occupies a single switching module slot in the CoreBuilder 9000 7-slot
chassis, 8-slot chassis, or 16-slot chassis.
Key Features
The 10/100BASE-TX and 100BASE-FX FEN Switching Modules support
the following key features:
■
Hot-swapping of modules
■
Management using the Administration Console
(a command line interface), the Web Management suite of
applications with an Internet browser, or SNMP-based applications
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 10-Port 100BASE-FX and 20-Port 10/100BASE-TX Fast Ethernet Layer 2 Switching Modules Quick Start Guide For information about the software features that these modules support, see the: ■ CoreBuilder 9000 Implementation Guide ■ Command Reference Guide ■ CoreBuilder 9000 Release Notes for the Fast Et...
10-Port 100BASE-FX and 20-Port 10/100BASE-TX Fast Ethernet Layer 2 Switching Modules Quick Start Guide 3 Audience Description This guide is intended for trained technical personnel only. Do not attempt to install, remove, or replace the 10/100BASE-TX or 100BASE-FX FEN Switching Modules if you have n...
4 10-Port 100BASE-FX and 20-Port 10/100BASE-TX Fast Ethernet Layer 2 Switching Modules Quick Start Guide ESD Safety Information Electrostatic discharge (ESD) can damage components of the module. ESD, which occurs when a module is improperly handled, can cause complete or intermittent failures. CAUTI...
